Cart 2 india

Specification
Brand : LANKEGU
BulletPoint1 : FEP 2.0 NFEP film is big improvement over traditional fep film: Better durability, fewer layer lines, accurate print results, Great for Resin Printing.
BulletPoint2 : High print success rate: NFEP Film offers excellent peel performance over standard FEP film. As such you will have much less failed prints as compared to using FEP films, and prints don't stick to nfep nearly.
BulletPoint3 : High transmittance: The 3D release nfep film has high transmittance, and the transmittance is over 95%, which makes the printed products more perfect and provides product quality.
BulletPoint4 : Easy to install, thinner than fep: simply follow the instructions in the product description, you can easily replace the NFEP film in a few minutes. (NOTE: NFEP is softer than standard FEP and thus easier to scratch.Please use caution when installing and cleaning.)
BulletPoint5 : FEP 2.0 NFEP Film is the best choice for printing a perfect model: 380*260*0.127mm nFEP(PFA) Release Film fit for ELEGOO Juipter and Photon M3 Max 12.8-13.6 inch LCD resin 3D Printers.
ExternallyAssignedProductIdentifier1 : 792288778022
ExternallyAssignedProductIdentifier2 : 0792288778022
IncludedComponents : 2gt 6mm open timing belt with copper buckles
ItemName : LANKEGU 3 PCS FEP 2.0 nFEP Film 380x260x0.127mm, PFA (nFEP) Film Release Film for ELEGOO Juipter and Photon M3 Max 12.8-13.6inch LCD Resin 3D Printers
ItemPackageDimensions_Height : 33.2994 centimeters
ItemPackageDimensions_Length : 4.5974 centimeters
ItemPackageDimensions_Width : 4.699 centimeters
ItemTypeKeyword : 3d-printer-accessories
Manufacturer : LANKEGU
ModelNumber : LKG-3D-021
NumberOfBoxes : 1
NumberOfItems : 3
PackageLevel : unit
PartNumber : LKG-3D-021
ProductDescription :

NFEP Film is an upgraded version of FEP film, which is more durable and lasting than FEP, has a higher success rate, faster printing speed. 

Product information:

Product name: NFEP(PFA) Release Film

Product size: 380*260*0.127mm

Packge quantity: 3 PCS

290*210*0.127mm nFEP(PFA) Release Film fit for ELEGOO Juipter and Photon M3 Max LCD Resin 3D Printers.

6 advantages elaborate craft:

Better durability

Fewer layer lines

Faster Print Speed

High transmittance

Accurate Print Results

Smaller release force and less chance to stick to film

Installation Steps:

Step1 : Remove screws at the bottom of resin vat and take out the broken release film.

Step2 : Then place the release nfep film between two steel rims

Step3 : Finally put the installed steel wheel back into resin vat and tighten screws

NOTE： 

1. Be sure to remove the plastic protective cover on both sides of each sheet before mounting. 

2.  NFEP is softer than standard FEP and thus easier to scratch.Please use caution when installing and cleaning.

ProductSiteLaunchDate : 2022-10-30T02:58:21.246Z
Size : 380x260x0.127mm
Style : Single pneumatic
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredDgHzRegulation1 : not_applicable
SupplierDeclaredDgHzRegulation2 : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1