Cart 2 india

Specification
Brand : Fafeicy
BulletPoint1 : [POWERFUL 3D PRINTER CONTROL BOARD] - Equipped with an ESP32 module and supports Marlin 2.0 firmware. Compatible with LCD2004, 12864, MKS MINI12864 V3, and MKS TFT serial port screens.
BulletPoint2 : [8M FLASH MEMORY] - Built-in 8M byte flash memory chip for effective in various application scenarios.
BulletPoint3 : [USB FIRMWARE UPDATE] - Easily update firmware via USB and control your 3D printer through the built-in function.
BulletPoint4 : [HIGH PERFORMANCE MCU] - Utilizes the ESP32 WROOM 32U module, a dual-core 32-bit high-speed MCU with a clock up to 240MHz. Integrated module provides superior performance.
BulletPoint5 : [A4988 STEPPER MOTOR DRIVERS INCLUDED] - Comes with 5 A4988 micro stepper motor drivers. Operate bipolar stepper motors in multiple step modes with output drive capabilities up to 35V and 2A.
Color : Gray
ExternallyAssignedProductIdentifier1 : 850064863949
ExternallyAssignedProductIdentifier2 : 0850064863949
GpsrSafetyAttestation : 1
IncludedComponents : Gray 5M with Tube Cutter
ItemLength : 5 meters
ItemName : 3D Printer Control Board ESP32 240MHz MCU with USB Update Firmware, 32 Bit MCU 8M Flash, A4988 Stepper Motor Driver for MKS Mini12864 V3
ItemPackageDimensions_Height : 7 centimeters
ItemPackageDimensions_Length : 22 centimeters
ItemPackageDimensions_Width : 14 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : 3d-printer-controllers
Manufacturer : Fafeicy
Material : Polytetrafluoroethylene (PTFE)
ModelName : Gray 5M with Tube Cutter
ModelNumber : Fafeicyngmx6s9fed
NominalWallThickness : 0.625 millimeters
NumberOfItems : 1
PackageLevel : unit
PartNumber : Fafeicyngmx6s9fed
ProductDescription : Spec:

Item Type: 3D Printer Motherboard
Material: PCB
Motherboard Model: For MKS TinyBee V1.0
MCU: ESP32 WROOM 32U
MCU Frequency: 240MHz
Memory: 520K
Input Power Supply: DC12-24V Heater: 2 heater ends, 1 heater bed
Temperature ADC: 3 NTC100K: TH1, TB, TH2 (requires jumper selection)
Motor Interface: 5 axes 6 motor interface (dual Z axes parallel connection)
Step Drive Mode: STEP DIR Moode
Drive : Supports external high current drive
Subdivision Settings: Dial switch
LCD Interface: Supports LCD 2004 12864, MKS MINI12864 V3
Serial Port: Reserved USART2 for MKS TFT series screen
End Stop: X, Y, Z, MT_DET
3D Touch Control: Support
Power : Supports power reverse and powerprotection
Motor Back Electromotive Force: Can be absorbed by phase sequence to preserve stepper driver
Firmware: For Marlin2.0. X
Firmware Update Method: USB drive upload
Small Memory Card: Shipped without card
A4988 Driver Features and Advantages:
1. Low RDS (on) output
2. Automatic current decay mode detection or selection
3. Mixing with slow current decay mode
4. Synchronous rectification, low power consumption
5. Internal undervoltage locking
6. Constant current
7. 3.3 and 5V compatible logic power supply
8. Thermal shutdown circuit
9. Grounding fault
10. Load short circuit
11. Five selectable stepper modes: full step, 1/2, 1/4, 1/8, and 1/16

Package List:
1 x 3D Printer Motherboard (Small Memory Card Not Included)
1 x USB Data Cable
5 x A4988 Micro Stepper Motor Driver
5 x Driver Heat Sink



ProductSiteLaunchDate : 2025-03-06T00:00:00.000Z
Size : 5M with Tube Cutter
SpecificUsesForProduct : 3D Printing
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredDgHzRegulation1 : not_applicable
SupplierDeclaredDgHzRegulation2 : not_applicable
SupplierDeclaredDgHzRegulation3 : not_applicable
SupplierDeclaredDgHzRegulation4 : not_applicable
SupplierDeclaredDgHzRegulation5 : not_applicable
UnitCount : 16.4
UnspscCode : 43201500