Cart 2 india

Specification
Brand : YWBL-WH
BulletPoint1 : USB Update Firmware: The motherboard can update firmware through USB and connect to the network and web pages through function to control the 3D printer.
BulletPoint2 : 3D Printer Control Board: With onboard ESP32 , supports for Marlin 2.0 firmware. In addition to supporting regular LCD2004 and 12864 screens, also supports MKS MINI12864 V3 and MKS TFT serial port screens.
BulletPoint3 : A4988 Driver: Comes with 5 pcs A4988 micro stepper motor drivers, which are built in converter, easy to operate, can operate bipolar stepper motors in full step, half step, 1/4, 1/8, 1/16 step modes, with output drive capabilities up to 35V and 2A.
BulletPoint4 : 8m Flash Memory: The module has a built in 8M byte flash memory chip, which provides effective for more application scenarios.
BulletPoint5 : 32 Bit MCU: The motherboard uses ESP32 WROOM 32U module, which embeds a core 32 bit high speed MCU with a clock up to 240MHz. And integrated module, the performance is very powerful.
Color : Blue
CompatibleDevices : Printer
GraphicsCardInterface : integrated
ItemName : 3D Printer Motherboard ESP32 240MHz MCU Control Board with 5Pcs A4988 Stepper Motor Driver DC12‑24V
ItemPackageDimensions_Height : 7 centimeters
ItemPackageDimensions_Length : 22 centimeters
ItemPackageDimensions_Width : 14 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : 3d-printer-controllers
Manufacturer : YWBL-WH
MemoryClockSpeed : 240 MHz
ModelName : Ywbl-wht3e2vzrskn
ModelNumber : YWBL-WHt3e2vzrskn
NumberOfItems : 1
OperatingTemperature : 25 degrees_celsius
PartNumber : YWBL-WHt3e2vzrskn
ProductDescription :

Specification:
Item Type: 3D Printer Motherboard
Material: PCB
Motherboard Model: For MKS TinyBee V1.0
MCU: ESP32 WROOM 32U
MCU Frequency: 240MHz
Memory: 520K
Input Power Supply: DC12-24V Heater: 2 heater ends, 1 heater bed
Temperature ADC: 3 NTC100K: TH1, TB, TH2 (requires jumper selection)
Motor Interface: 5 axes 6 motor interface (dual Z axes parallel connection)
Step Drive Mode: STEP DIR Moode
Drive: Supports external high current drive
Subdivision Settings: Dial switch
LCD Interface: Supports LCD 2004 12864, MKS MINI12864 V3
Serial Port: Reserved USART2 for MKS TFT series screen
End Stop: X, Y, Z, MT_DET
3D Touch Control: Support
Power : Supports power reverse and power peak
Motor Back Electromotive Force: Can be absorbed by phase sequence to preserve stepper driver
Firmware: For Marlin2.0. X
Firmware Update Method: USB drive upload
Small Memory Card: Shipped without card
A4988 Driver Introduction: A4988 is a complete micro stepper motor driver with built in converter, easy to operate. The bipolar stepper motor can operate in full step, half step, 1/4, 1/8, and 1/16 step modes, with an output drive capacity of up to 35V and ±2A. A4988 includes a fixed off time current regulator that is in slow or mixed decay mode. The A4988 converter is the key to easy implementation. The step input only requires one pulse to drive the motor forward one microstep. There is no phase sequence table, control line, or complex programming interface. The A4988 interface is very suitable for situations where complex microprocessors are unavailable or overloaded.

Packing List:
1 x 3D Printer Motherboard (Small Memory Card Not Included)
1 x USB Data Cable
5 x A4988 Micro Stepper Motor Driver
5 x Driver Heat Sink

ProductSiteLaunchDate : 2023-11-22T10:08:32.953Z
SupplierDeclaredDgHzRegulation : not_applicable
SystemBusStandardSupported : SATA 3
UnspscCode : 43201500