Cart 2 india

Specification
Brand : BIGTREETECH
BulletPoint1 : BIGTREETECH Manta M8P V2.0 Control Board uses 32-bit ARM Cortex-M7 series STM32H723ZET6 main control chip with a core frequency of 550MHz. High efficiency MOSFET for less heat generation
BulletPoint2 : The power chip of Manta M8P V2.0 integrated main control board adopts TPS5450-5A, which supports DC12/24V power input; the output current of this chip is up to 5A, and the peak value can reach 6A, which perfectly supports the power supply of Raspberry-Pi
BulletPoint3 : The control board and the core board use BTB connection method, so that other core board solutions other than CM4 can be selected, such as BIGTREETECH CB1. The mainboard reserves the SPI expansion interface for using the Klipper firmware to connect an external acceleration sensor for acceleration compensation
BulletPoint4 : The thermistor can select the pull-up resistance value through the jumper, which supports PT1000 without external modules, which is convenient for DIY use; the control board reserves a three-way four-wire fan interface, which can be used to connect a water cooling device
BulletPoint5 : The MCU firmware can be upgraded through SD card, or through DFU through Klipper's make flash command; the main board reserves the proximity switch interface, supports NPN and PNP type selection, (24V, 12V, 5V) voltage optional, shared with VFAN6 Voltage selection
BulletPoint6 : BIGTREETECH Manta M8P V2.0 reserves rich installation interfaces: material breakage detection, shutdown after completion BLTouch、RGB、I2C、 Servo interface, 5V power-off detection, three-way four wire fan interface, proximity switch interface, SPI expansion interface. And annotate in detail in the display image, you can connect to your 3D printer according to the corresponding annotations.
ChipsetType : Intel C622
Color : Red
CompatibleDevices : Printer
CompatibleProcessorTypes : STM32F207VCT6, STM32F407VGT6
CustomerPackageType : Standard Packaging
ExternallyAssignedProductIdentifier1 : 778365968586
ExternallyAssignedProductIdentifier2 : 0778365968586
GraphicsCardInterface : integrated
IncludedComponents : BIGTREETECH Manta M8P V2.0 Control Board
ItemName : BIGTREETECH Manta M8P V2.0 Integrated Control Board 32Bit Running Klipper with CB1, High Speed 3D Printer Motherboard, Compatible TMC5160T Plus,TMC5160,TMC2209,TMC2240 Stepper Driver (Without CB1)
ItemPackageDimensions_Height : 20.8026 centimeters
ItemPackageDimensions_Length : 5.207 centimeters
ItemPackageDimensions_Width : 14.097 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : 3d-printer-controllers
MainPowerConnectorType : 24-Pin
Manufacturer : BIGTREETECH
Material : PCB
MemoryClockSpeed : 120 MHz
MemorySlotsAvailable : 6
MemoryStorageCapacity : 64 GB
ModelName : BIGTREETECH CEB V1.0
ModelNumber : KINGPRINTER-1020000442
NumberOfItems : 1
NumberOfPorts : 7
OperatingTemperature : 20 degrees_celsius
PartNumber : KINGPRINTER-1020000442
Platform : android
ProductDescription : BIGTREETECH Manta M8P V2.0 integrated Control Board
Additional Product Features
1. The main board reserves BOOT button, can update the motherboard boot program through DFU;
2. Increase protection circuit of the thermistor to prevent the control chip from burning due to leakage of the hot bed or heating rod;
3. The 24V, 12V, 5V voltage of the CNC fan is optional, which saves the operation of external transformer module, thereby reducing the probability of damage to the motherboard;
4. The MCU firmware can be upgraded through SD card, or the MCU firmware can be updated through DFU through Klipper's make flash command;
5. On-board TMC-driven SPI and UART working modes, on-board DIAG function pins, can be used by simply plugging and unplugging the jumper cap;
6. Support material break detection, shutdown, BLTouch, RGB lights and other functions;

Product Parameters
1. Logic voltage: DC3.3V
2. Drive input voltage: 24V, HV (24-60V) optional
3. Mainboard input voltage: VIN=DC12V or DC24V
4. Hot bed input voltage: BED IN=DC12V or DC24V
5. Heating interface: hot bed (HB), heating rod (HE0,HE1,HE2,HE3)
6. The maximum output current of the hot bed port: 10A, peak value 10.5A
7. Maximum output current of heating rod port: 5.5A, peak value 6A
8. Fan interface: 5-way two wire CNC fan (FAN0, FAN1, FAN2, FAN3, FAN4, Pi FAN), 2-way four wire CNC fan (FAN5, FAN6), 1-way normally open fan. The CNC fan voltage (5V, 12V, 24V) is optional;
9. Maximum output current of fan interface: 1A, peak value 1.1A
10. Total current of heating rod + driver + fan: less than 12A
11. Temperature sensor interface: 5 channels of 100K NTC, 4 of which are optional ports for NTC and PT1000
12. Display: Serial touch screen, SPI touch screen, LCD display
13. PC communication interface: Type-C
14. Support machine structure: Cartesian, Delta, Kossel, Ultimaker, CoreXY
ProductSiteLaunchDate : 2023-09-06T10:10:01.776Z
Size : Small
Style : Manta M8P V2.0
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
SystemBusStandardSupported : SATA 1
TotalUsbPorts : 2
UnspscCode : 43201513
Voltage : 24 volts_of_direct_current