Cart 2 india

Specification
Brand : TOPINCN
BulletPoint1 : Efficient Heat Dissipation: This 3D printer control board uses MOSFET for better heat dissipation, 12 to 24V power input, reducing the heating bed current by 1/4, effectively solving the Mosfet heating problem.
BulletPoint2 : Multifunction: You can design your own boot and all buttons, at least 15 command buttons can be customised, you can design your own boot and all buttons. Support for breakpoints, power saving, power failure detection, automatic shutdown, etc.
BulletPoint3 : Main Usage: The 3D printer mainboard controller is plug and play on for Ender series printers with the BTT SKR MINI E3 V3.0 control board.
BulletPoint4 : Remote Printing: The 3D printer mainboard controller can be easily upgraded with firmware via storage card, with high speed module, access to the to achieve remote printing. It supports setting the stepper drive current in the config file, so you no longer have to worry about adjusting the current to burn the mainboard.
BulletPoint5 : Excellent Sensitivity: The 3D printer control board uses a 32 bit high speed chip and the self developed main board.
ItemName : Integrated Mainboard Controller, PCB 12V To 24V 3D Printer Control Board for Architectural Design (Separate Mainboard Model)
ItemPackageDimensions_Height : 5 centimeters
ItemPackageDimensions_Length : 25 centimeters
ItemPackageDimensions_Width : 17 centimeters
ItemTypeKeyword : 3d-printer-controllers
Manufacturer : TOPINCN
ModelNumber : TOPINCNab2vpige01-11
NumberOfItems : 1
PartNumber : TOPINCNab2vpige01-11
ProductDescription : 1. Excellent Sensitivity: The 3D printer control board uses a 32 bit high speed chip and the self developed main board.
2. Remote Printing: The 3D printer mainboard controller can be easily upgraded with firmware via storage card, with high speed module, access to the to achieve remote printing. It supports setting the stepper drive current in the config file, so you no longer have to worry about adjusting the current to burn the mainboard.
3. Multifunction: You can design your own boot and all buttons, at least 15 command buttons can be customised, you can design your own boot and all buttons. Support for breakpoints, power saving, power failure detection, automatic shutdown, etc.
4. Efficient Heat Dissipation: This 3D printer control board uses MOSFET for better heat dissipation, 12 to 24V power input, reducing the heating bed current by 1/4, effectively solving the Mosfet heating problem.
5. Main Usage: The 3D printer mainboard controller is plug and play on for Ender series printers with the BTT SKR MINI E3 V3.0 control board.

Spec:
Item Type: 3D Printer Control Board
Material: PCB
Opening Size: Approx. 102 x 76mm / 4.02 x 2.99in
External Size: Approx. 110 x 84mm / 4.33 x 3.31in
Processor: STM32
Input Voltage: 12V to 24V 5A to 15A
Stepper Driver: 4988, 8825, 8729, 2100, 2208...
Temperature Sensor Interface: NTC100K, 31855
TFT Screen: 3.5 (inch)
Print File Format: G code
Supported Machine Build: for XYZ, for delta, for kossel, for corexy
Recommended Software: for Cura, for Simplify3d, for Pronterface, for Prpetier Host
Firmware Upgrade: Storage card

How to Use:
Use according to the selling point chart introduction

packing list:
1 x3D Printer Control Board
1 x USB Blue Cable
or1 x 3D Printer Control Board
1 x USB Blue Cable
1 x TFT35 3.5 Inch
1 x Cable

ProductSiteLaunchDate : 2023-12-23T00:00:00.000Z
Size : Separate Mainboard Model
UnitCount : 1
UnspscCode : 43201513