Cart 2 india

Specification
Brand : LLPT
BulletPoint1 : LLPT 94 Adhesion Promoter is a liquid adhesion promoter and commonly used on low surface energy materials to increase the initial bonding strength and curing better for long term performance of adhesive, LLPT suggests each application should be tested on compatibility in a small range before large area application for the first time use.
BulletPoint2 : Use gravity feed wipe, knurled roller or brush to apply a thin, uniform coating thickness onto bonding surfaces, which is approximately 0.002 inch (0.05 mm) or less.
BulletPoint3 : The bonding surface should be clean and dry. Apply promoter only to areas that will be fully covered with tape and a drying time of 30 to 90 seconds is recommended.
BulletPoint4 : Extremely helpful for Acrylic Double Sided Adhesive for a secured bonding initial bonding, specially for permanent use.
BulletPoint5 : Not only works on LLPT double sided acrylic mounting foam tapes, but also any other brands and compatible with 4298 Adhesion Promoter.
Color : Clear
CompatibleMaterial : Acrylic
CoreSize : 2.0 inches
ExternallyAssignedProductIdentifier : 4987167046064
ExternallyAssignedProductIdentifier1 : 885114805488
ExternallyAssignedProductIdentifier2 : 4042448077424
ExternallyAssignedProductIdentifier3 : 0885114805488
ExternallyAssignedProductIdentifier4 : 8855058389551
ExternallyAssignedProductIdentifier5 : 04042448077424
GpsrSafetyAttestation : 1
ItemForm : Liquid
ItemName : LLPT 94 Adhesion Promoter 2 Pack 18ml Each Bottle Adhesive Primer for Acrylic Double Sided Mounting Molding and Foam Tape
ItemPackageDimensions_Height : 9.7028 centimeters
ItemPackageDimensions_Length : 6.1976 centimeters
ItemPackageDimensions_Width : 9.6012 centimeters
ItemPackageQuantity : 2
ItemTypeKeyword : adhesive-primers
ItemVolume : 18 milliliters
Manufacturer : LLP International Group
Material : Epoxy Resin
ModelNumber : LLPT94
NumberOfItems : 1
OperationMode : Manual
PackageLevel : unit
PartNumber : LLPT94018ml
ProductDescription :

APPLICATION INSTRUCTION:

1. Substrate formulations and surface energies may vary for different materials; each application should be tested for compatibility in a small range before large area application.
2. Wear gloves when you use this product to avoid any skin injury and see doctor immediately if swallow this product by accident.
3. The bonding surface should be clean and dry. Contaminated surface should be cleaned with isopropyl alcohol or acetone solvent.
4. Shake the bottle gently before using.
5. Use gravity feed wipe, knurled roller or brush to apply a thin, uniform coating thickness onto bonding surfaces, which is approximately 0.002 inch (0.05 mm) or less.
6. Apply promoter only to areas that will be fully covered with tape and a drying time of 30 to 90 seconds is recommended.


SPECIAL NOTES:

Completely use up this liquid contents as soon as possible after opening or seal securely for next use. Apply a thin, uniform coating to the bonding surface, using the minimum amount that will fully coat the surface.

Suitable on low surface energy materials before tape application to increase the initial bonding; operation temperature is between 60oF - 90 oF; coverage: approximately 75 m2 (800 ft2 ) per gallon (Based on 0.002 inch wet coating thickness). Cyclohexane: 45-50%; M-Xylene: 10-15%; O-Xylene: 5-12%; Ethylbenzene: 3-5%; Epoxy: 0.1-1%.
ProductSiteLaunchDate : 2023-10-27T07:04:04.399Z
RecommendedUsesForProduct1 : Sewing
RecommendedUsesForProduct2 : Packaging
Size : 18ml x 2 Pack
Style : 6400 (01)
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
SurfaceRecommendation : Cloth
TensileStrength : 30 pounds_per_inch
UnitCount : 1.2
UnspscCode : 31201600
Viscosity : Low Viscosity
WaterResistanceLevel : not_water_resistant