Cart 2 india

Specification
Brand : Simpson Strong-Tie
BulletPoint1 : Thread design undercuts to efficiently transfer the load to the base material
BulletPoint2 : Serrated cutting teeth and thread design enable quick and easy installation
BulletPoint3 : Specialized heat-treating process creates greater hardness at the tip to facilitate cutting while the body remains ductile
BulletPoint4 : Designed to install using a rotary hammer or hammer drill with standard ANSI drill bits no special tools required
BulletPoint5 : Code listed for cracked and uncracked concrete applications; UL/FM listed
Color : Silver
CustomerPackageType : Standard Packaging
DriveSystem : Phillips
ExteriorFinish : Stainless Steel
ExternallyAssignedProductIdentifier1 : 707392306511
ExternallyAssignedProductIdentifier2 : 0707392306511
ExternallyAssignedProductIdentifier3 : 00707392306511
GradeRating : Industrial
ItemDisplayDimensions_Height : 3.67 inches
ItemDisplayDimensions_Length : 4 inches
ItemDisplayDimensions_Width : 0.98 inches
ItemName : Simpson Strong-Tie THD50234RH Titen HD® 3/8 in. x 2-3/4 in. Threaded Rod Hanger for 1/2-in. Rod (50-Qty)
ItemPackageDimensions_Height : 9.398 centimeters
ItemPackageDimensions_Length : 10.16 centimeters
ItemPackageDimensions_Width : 32.512 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : concrete-screws
Manufacturer : Simpson Strong Tie
Material : Stainless Steel 410
Material1 : Zinc
Material2 : Carbon Steel
MaximumShearStrength : 1,200 lbf
MeasurementSystem : Imperial
MetalType : Stainless Steel
MetalType1 : Zinc
MetalType2 : Alloy Steel
ModelName : THD50234RH
ModelNumber : THD50234RH
NumberOfBoxes : 1
NumberOfItems : 1
NumberOfPieces : 10
PartNumber : THD50234RH
ProductDescription : Applications: The anchor is made from 410 Stainless Steel, and is Silver Climaseal Coated. This anchor is designed for use in Concrete, Block, and Brick. Environment: The anchor is designed for use in a Moist environment. Head Style: The anchor is a Flat Countersunk Phillips head and is designed to prevent the head from protruding above the surface of the item being attached. Hole Diameter/Bit Diameter: The anchor requires a 3/16" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill. Driver Required: A #3 is required for driving the anchor into the base material. Diameter of Anchor: The diameter of the anchor is 1/4". Length Anchor: The length of the anchor is 2-3/4". Thread Length: The length of the threads on the anchor is 1-3/4" in length. Minimum Embedment: The minimum anchor embedment into the concrete is 1". Therefore, the anchor must be installed so that a minimum of 1" of the anchor is embedded into the concrete. Maximum Fixture Thickness: The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-3/4". This will ensure that the minimum embedment of 1" will be met. Fixture Hole Diameter: The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/4" diameter anchor requires the hole in the fixture to be 5/16". Spacing between Anchors: Each anchor must be spaced a minimum distance of 4" from each other when measured center to center. Edge Distance: It is very important not to install the anchor any closer than 3" from an unsupported edge of the concrete.
ProductSiteLaunchDate : 2012-08-31T00:00:01-00:00
Size : 1/4"
Style : Machine Screw Anchor Setting Tool
SupplierDeclaredDgHzRegulation : unknown
UnitCount : 1
UnspscCode : 31161500