Cart 2 india

Specification
Brand : Hillman
BulletPoint1 : State of the art thread design cuts into concrete
BulletPoint2 : Tapper screws are designed for fastening applications in concrete, block and brick
BulletPoint3 : Use Tapper screws to attach electrical equipment, two by fours, downspout straps, hose reels, flag poles, Hurricane shutters and more
BulletPoint4 : BLUE Parma-Seal coated
BulletPoint5 : For use with treated lumber
BulletPoint6 : BLUE Parma-Seal coated
BulletPoint7 : For use with treated lumber
BulletPoint8 : Building code approved
Color : No Color
DriveSystem : Phillips
ExteriorFinish : Blue Perma Seal
ExternallyAssignedProductIdentifier1 : 008236385731
ExternallyAssignedProductIdentifier2 : 0008236385731
ExternallyAssignedProductIdentifier3 : 00008236385731
ItemName : The Hillman Group 375309 Flat Head Phillips Tapper Concrete Screw Anchor, 1/4 x 2-1/4-Inch, 100-Pack
ItemPackageDimensions_Height : 12.9 centimeters
ItemPackageDimensions_Length : 7.8 centimeters
ItemPackageDimensions_Width : 8.5 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : concrete-screws
Manufacturer : The Hillman Group
Material : Plastic
MaximumShearStrength : 675 pounds_per_square_inch
MeasurementSystem : Metric
MetalType : Alloy Steel
ModelName : The Hillman Group 375309 Flat Head Phillips Tapper Concrete Screw Anchor, 1/4 x 2-1/4-Inch, 100-Pack
ModelNumber : 375309
NumberOfItems : 100
NumberOfPieces : 100
PackageLevel : unit
PartNumber : 375309
ProductDescription : Applications
The anchor is made from Carbon Steel, and is Blue. This anchor is designed for use in Concrete, Block, and Brick.

Environment
The anchor is designed for use in a Dry environment.

Head Style
The anchor is a Hex Washer head and is designed to allow the head to sit on top of the surface of the item being attached.

Hole Diameter/Bit Diameter
The anchor requires a 3/16" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Driver Required
A 5/16" nut driver is required for driving the anchor into the base material.

Diameter of Anchor
The diameter of the anchor is 1/4".

Length Anchor
The length of the anchor is 1-1/4"

Thread Length
The length of the threads on the anchor is 1-1/4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 1". Therefore, the anchor must be installed so that a minimum of 1" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 0" to 1/4". This will ensure that the minimum embedment of 1" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/4" diameter anchor requires the hole in the fixture to be 5/16".

Spacing between Anchors
Each anchor must be spaced a minimum distance of 4" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 3" from an unsupported edge of the concrete.
ProductSiteLaunchDate : 2007-02-17T04:53:08-00:00
Size : 1/4" x 2-1/4"
SupplierDeclaredDgHzRegulation : not_applicable
UnitCount : 100
UnspscCode : 31161500