Cart 2 india

Specification
AgeRangeDescription : adult
Amperage : 40 amps
BatteriesRequired : 1
Brand : YFUSET
BulletPoint : Industrial Motors
BulletPoint1 : This module Dimensions: 43mm (L) × 43mm (W) × 27mm (H) / 1.69in × 1.69in × 1.06in;Package Includes: 6PCS Dual H-Bridge Motor Driver Modules
BulletPoint2 : This module uses the L298N as the main driver chip, offering strong driving capability, low heat generation, and strong anti-interference capability.
BulletPoint3 : The module draws power from the drive source. To prevent damage to the voltage regulator chip, when using a drive voltage greater than 12V, please use an external 5V logic supply.
BulletPoint4 : The module uses a large-capacity filter capacitor and a freewheeling protection diode to improve reliability.
BulletPoint5 : This module is suitable for stepper motors, smart cars, and Arduino projects, and can drive two motors.
BulletPoint6 : 4. Start-stop :(1). low level input or when EN and COM are connected, the motor runs. (2). High level input the motor will slowly stops,
BulletPoint7 : 5. Brakingthe motor runs when the low level is added or EN and BRK are connected The motor brake stops when a high level is added or port suspension;
BulletPoint8 : 6. Peak current settingEquipped with a motor protection function, the driver provides options to set desired current number in the P-sv knob. Please note that the rate of change is ±10% .
BulletPoint9 : 7.Acceleration/deceleration time setting Set the acceleration time and deceleration time of the motor through the potentiometer ACC/DEC The acceleration and deceleration time can be increased or decreased by rotating ACC/DEC left or right. Setting range: 0.3-15s The acceleration time is the time required for the motor to reach the rated speed from the static state, The deceleration time is the time required for the motor to stop from the rated speed.
Color : Dark Gray
ExternallyAssignedProductIdentifier : 10752259628043
ExternallyAssignedProductIdentifier1 : 0768383220438
ExternallyAssignedProductIdentifier2 : 768383220438
ExternallyAssignedProductIdentifier3 : 00785901492337
IncludedComponents : GV3P32
ItemName : 6PCS L298N DC Stepper Motor Driver Board Module Dual H-Bridge Motor Driver Module for Arduino Robot Smart Car
ItemPackageDimensions_Height : 0.2 inches
ItemPackageDimensions_Length : 0.2 inches
ItemPackageDimensions_Width : 0.2 inches
ItemPackageQuantity : 6
ItemTypeKeyword : electric-motor-controls
Manufacturer : YFUSET
Material : Copper
ModelName : BLD-120
ModelNumber : ZGW-38
NumberOfBoxes : 1
NumberOfItems : 1
PartNumber : ZGW-38
ProductDescription :

Module Name: Dual H-Bridge Motor Driver Module

Module Weight: 30g / 1.06oz

Module Dimensions: 43mm (L) × 43mm (W) × 27mm (H) / 1.69in × 1.69in × 1.06in

Working Mode: H-Bridge Drive (Dual Channel)

Main Control Chip: L298N

Package Includes: 6PCS Motor Driver Modules

Logic Voltage: 5V

Drive Voltage: 5V-35V

Logic Current: 0mA-36mA

Drive Current: 2A (MAX per bridge)

Storage Temperature: -20℃ to +135℃

Maximum Power: 25W

Notes:

Typical Application: When the drive voltage is between 7V-12V, the onboard 5V logic power can be used. After using the onboard 5V supply, do not input voltage into the +5V interface, but you can output 5V for external use.

High Voltage Drive for Unconventional Applications: When the drive voltage is above 12V and less than or equal to 24V (the manual suggests supporting up to 35V, but based on usage experience, the L298N conservatively supports a maximum voltage of 24V), for example, when driving a motor rated at 18V, first remove the onboard 5V output to enable the jumper cap, then provide 5V voltage externally to the 5V output port to create a control signal at 5V. When this signal is valid and the power supply to the motor driver module is normal, the module will output current; otherwise, even if the power supply is normal, there will be no current to the motor. The voltage powers the internal logic circuit of the L298N.

ProductSiteLaunchDate : 2024-09-14T10:14:57.397Z
Size : PVF060 14mm Input
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
UnitCount : 1
UnspscCode : 26111500
Voltage : 600 volts