Cart 2 india

Specification
Brand : YEQIN
BulletPoint1 : Universal Cap/Hat Hoop
BulletPoint2 : Size: 5.25'' x 4.5''(133*114mm)
BulletPoint3 : this hoop will make your job easier for embroidering on hats. its designed to work with your existing 4x4 hoop or larger (not included). PE770
BulletPoint4 : Brother 700 750D 770, 780D / Simplicity SE2 , SE3, All White Embroidery Machines / Bernina Deco 500, Deco 600 Brother PE100, PE150, PE200, PE180
BulletPoint5 : Embroidery Machine Cap Hoop for Brother Babylock Singer Bernina Janome Singer Husqvarna Viking Pfaff
Color : Cap Hoop
CompatibleMaterial : Wood and Plastic Hoops
ExternallyAssignedProductIdentifier1 : 715627172008
ExternallyAssignedProductIdentifier2 : 0715627172008
ExternallyAssignedProductIdentifier3 : 00715627172008
Flavor : No
GpsrSafetyAttestation : 1
IncludedComponents : Magnetic frame
IsElectric : 1
ItemDisplayDimensions_Height : 8.5 inches
ItemDisplayDimensions_Length : 0.3 inches
ItemDisplayDimensions_Width : 0.25 inches
ItemDisplayWeight : 0.1 pounds
ItemName : YEQIN Universal Cap/Hat Hoop, Embroidery Machine Cap Hoop for Brother Babylock Singer Bernina Janome Singer Husqvarna Viking Pfaff
ItemPackageDimensions_Height : 26.3906 centimeters
ItemPackageDimensions_Length : 4.0894 centimeters
ItemPackageDimensions_Width : 16.9926 centimeters
ItemPackageQuantity : 1
ItemShape : Rectangular
ItemTypeKeyword : embroidery-hoops
Language : english
Manufacturer : YEQIN
Material : Plastic
ModelName : PE900
ModelNumber : PE900
NumberOfItems : 1
PackageLevel : unit
PartNumber : PE900, SAMF180N
Pattern : Solid
PowerSourceType : ac_dc
ProductDescription : Ready to Be Embroidered on in Seven Simple Steps Easy and convenient the baseball cap can be hooped and ready to be embroidered on in seven simple steps.

- Step 1 - Pull shiny backing off of adhesive stabilizer. Adhere to the bottom of the Cap Hoopster. Make sure the stabilizer is taught and firmly attached to the Cap Hoop, allowing it to wrap around the edges of the Cap Hoopster if necessary.

- Step 2 - Determine where design should go onto the cap. The use of a water-soluble pin will help center design. Just make sure a vertical and horizontal line intersecting at the center point of the design.

- Step 3 - Loosen visor clamp by turning thumbscrew. Attach clear template with two holes to the two small pegs on the visor clamp. Loosen back strap on cap and slide the visor under the template and visor clamp. Center the area of the cap that will be embroidered. The markings on the cap and the template will help you to do this.

- Step 4 - Make sure sweat band is pulled back before you tighten down on thumbscrew. a) You must prevent the sweatband from being stitched to the cap. Taping or pinning the sweat band may be necessary. b) Stand-up buckram (a non-fused backing) must be pulled back with sweatband. Cutting buckram liner an inch or two on each side, where it is stitched to the visor, will allow it to be pulled back neatly.

- Step 5 - Press the cap down against the adhesive backing starting in the middle and working out. The cap must be as flat and smooth as possible.

- Step 6 - Clamp the Cap Hoopster to the outer machine hoop on the side opposite where the machine hoop attaches to the embroidery unit.

- Step 7 - Turn your machine on and set it up for embroidery as usual. Turn embroidery unit on and attach attach machine hoop. You may have to remove the foot and/or shank to do this. Use curser keys to center needle and begin to embroider designs onto the cap.

Remember, design must be rotated clockw
ProductSiteLaunchDate : 2018-06-02T07:00:00.000Z
RecommendedUsesForProduct : Sewing
Size : Cap Hoop
StreetDate : 2022-07-25T00:00:01Z
Style : PE900 + Frame
SupplierDeclaredDgHzRegulation : not_applicable
SurfaceRecommendation1 : Plastic
SurfaceRecommendation2 : Wood
TargetAudienceKeyword1 : embroiderers
TargetAudienceKeyword2 : Adults
TargetAudienceKeyword3 : Seniors
TargetAudienceKeyword4 : commercial
UnitCount : 1
UnspscCode : 49221500
WaterResistanceLevel : not_water_resistant