Cart 2 india

Specification
Brand : USA Knifemaker Supply
BulletPoint1 : Shortest (most collapsed) is .60” OAL Longest is: .95” OAL
BulletPoint2 : The female tube is .150” in diameter but when the male is pounded it, the tube will expand to .165”
BulletPoint3 : Drill your holes in the scales and tang to at least .165”
BulletPoint4 : The top “head” is .045” thick The top head diameter is: .249”
BulletPoint5 : Each pack is 25, 500 or 1000 pack. The numbers are a pair.
Color : Brass
ExteriorFinish : Zinc
ExternallyAssignedProductIdentifier1 : 743562763593
ExternallyAssignedProductIdentifier2 : 0743562763593
GpsrSafetyAttestation : 1
GradeRating : Standard
ItemName : Cutlers Rivets in Brass-.60” to .95” Long (10)
ItemPackageDimensions_Height : 6.35 centimeters
ItemPackageDimensions_Length : 0.6096 centimeters
ItemPackageDimensions_Width : 3.048 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : leathercraft-rivets
Manufacturer : USA Knifemaker
Material : Brass
Material1 : copper
Material2 : leather
MeasurementSystem1 : Imperial
MeasurementSystem2 : Metric
MetalType : Iron
ModelName : 2b
ModelNumber : 2b
NumberOfItems : 10
NumberOfPieces : 20
PartNumber : Cutler#2
ProductDescription : These are traditional cutlers rivets. To use them, pound the male solid shank side into the female tube side and they will hold tight. Really tight. This style handle fastener is still widely used today after a hundred or more years because it works so well. It’s quick, easy and holds fast. Your commercial kitchen knives almost certainly use some form of cutlers rivets. This Cutlers rivet will fit a knife handle stack (2 scales and tang) that is .60” thick up to .95” thick when countersunk. This is going to cover nearly every knife handle thickness in your kitchen and most hunting knives. Tip: You can counter sink the heads or leave them proud. It has been done both ways historically but certainly countersunk is more widely used. To countersink the heads, trial and error drilling into your handle material until the head is flush or even below the surface and sand down the handle material flush to the head. The countersink hole bottom does not have to be flat. If you want a flat bottomed hole, grind the tip of a ¼” drill bit flat. It will cut enough to get the job done. You are only countersinking this .045” Tip: Try not to undersize the hole in wood or other natural material. When you pound these together the shank is going to expand putting pressure on the wood and over time the wood is going to crack from humidity changes. Wood always loses. G10, Micarta or other high pressure laminate or phenolic don’t change size so much and are quite a bit tougher so this is less of a concern. Better to have the shank hole a little oversize than undersized. It’s OK to use epoxy with these to seal the scale but it isn’t required.
ProductSiteLaunchDate : 2024-03-15T20:18:54.136Z
Size : Silver
Style : Elegant
SupplierDeclaredDgHzRegulation : unknown
SupplierDeclaredDgHzRegulation1 : not_applicable
SupplierDeclaredDgHzRegulation2 : not_applicable
SupplierDeclaredDgHzRegulation3 : not_applicable
SupplierDeclaredDgHzRegulation4 : not_applicable
SupplierDeclaredDgHzRegulation5 : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
TargetAudienceKeyword : Adults
UnitCount : 31
UnspscCode : 53141500
WarrantyDescription : 90