Cart 2 india

Specification
Amperage : 6 amps
Brand : Yanmis
BulletPoint : Reland Sung
BulletPoint1 : ➤【L298N Main Control Chip】L298N as main driver chip makes strong driving ability/small heating/strong anti-interference/low calorific value
BulletPoint2 : ➤【-channel H-bridge】-channel H-bridge driver working mode creates higher working efficiency
BulletPoint3 : ➤【Better heat dissipation】There is a big heat sink on board for better heat dissipation
BulletPoint4 : ➤【Specifications】Work Mode: H bridge drive (-channel) ; Main Control Chip: L298N ; Logic Voltage: 5V ; Drive Voltage: 5V-35V ; Logic Current: 0mA-36mA ; Drive Current: 2A( single-bridge) ; Storage Temperature: -20℃ to +135℃ ; . Power: 25W
BulletPoint5 : ➤【Note】5V enable is a control with a 5V level; when the input is valid and power supply of motor drive module is normal, motor driver module outputs current. Otherwise, even if the power supply is normal, there is no current on motor.
Color : Red
ExternallyAssignedProductIdentifier1 : 749249368860
ExternallyAssignedProductIdentifier2 : 0749249368860
ItemName : L298N Driver Module, H-Bridge Robot Stepper Motor Control and Drives Module for Stepper Motor Smart Car Robot Power Control
ItemPackageDimensions_Height : 6 centimeters
ItemPackageDimensions_Length : 3 centimeters
ItemPackageDimensions_Width : 6 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : electronic-component-motor-drives
Manufacturer : Yanmis
Material : Copper
ModelNumber : BTS7960
MountingType : Surface Mount
NumberOfChannels : 2
NumberOfItems : 1
OutputVoltage : 240 volts
PackageTypeName : Surface Mount Technology (SMT) package
PartNumber : Yanmisd406mwyn9v
ProductDescription : Product features:
This motor driver has strong driving ability, low heat, strong anti-jamming ability.
H-bridge two-channel type driver, drive voltage is 5V to 35V, drive current is 2A.
For better heat dissipation is a large heat sink on board. Practical to use, with screw terminals for easy wiring. It is usually used to drive stepper motors on smart cars or robots.

Specifications:

Working mode: H-bridge drive (-channel)
Main control chip: L298N
Logic voltage: 5V
Drive voltage: 5V-35V
Logic current: 0mA-36mA
Drive current: 2A ( single-bridge)
Storage temperature: -20 to + 135
. Power: 25W
Size: 4.5 * 4.5 * 2.8cm / 1.7 * 1.7 * 1.1in
Weight: 27g (approx.)

Annotation:
1. When the operating voltage is 7V-12V, a 5V on-board logic voltage can be used as the power supply. If you use 5V as a power supply on board, do not input voltage to the + 5V terminal, but this may result in an external 5V voltage. (This is a regular application)
2. If the operating voltage is higher than 12 V and less than or equal to 24 V, for example to operate a motor with a rated voltage of 18 V, you must first pull out the jumper of the 5 V output enable. Then connect 5V to the 5V output is external.
5V enable is a control with a 5V level; If the input is valid and the motor drive module power supply is normal, the motor driver module will output power. Otherwise, even if the power supply is normal, there is no power on the motor.

Package contents:

1 x motor driver

ProductSiteLaunchDate : 2019-05-15T14:24:16.711Z
SupplierDeclaredDgHzRegulation : not_applicable
UnspscCode : 26111500
Voltage : 12 volts
Wattage : 1069 watts