Cart 2 india

Specification
Brand : Envistia
BulletPoint1 : Using only two pins, controls 16 free-running PWM outputs. 12-bit resolution for each output. For servos, that means about 4us resolution at 60Hz update rate
BulletPoint2 : IIC I2C Communications Interface, 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs
BulletPoint3 : It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages).
BulletPoint4 : Configurable push-pull or open-drain output
BulletPoint5 : Adjustable frequency PWM up to about 1.6 KHz
CurrentRating : 0.5 amps
ExternallyAssignedProductIdentifier1 : 0732387203551
ExternallyAssignedProductIdentifier2 : 732387203551
ItemDisplayWeight : 2.56 pounds
ItemName : PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot
ItemPackageDimensions_Height : 0.5 inches
ItemPackageDimensions_Length : 6 inches
ItemPackageDimensions_Width : 4 inches
ItemPackageQuantity : 1
ItemTypeKeyword : electronic-component-motor-drives
Manufacturer : Envistia Mall
Material : Copper
MinimumFrequency : 50 hertz
NumberOfItems : 1
PackageLevel : unit
PartNumber : PCA9685 Module
ProductDescription :

This PCA9685 16-Channel 12-Bit PWM Servo Driver can help a lot when there are insufficient PWM output pins for the MCU in your project. Make a robot, hexapod walker, or drive multiple LEDs with precise PWM control.

Using only two pins, control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs. Simply enable the I2C communication between the MCU and the PCA9685 16-channel 12-bit PWM driver, so as to control multiple servos simultaneously.

Features:

• i2c-controlled PWM driver with a built-in clock. That means that you do not need to continuously send it a signal, tying up your microcontroller. It is completely free running!
• 5V compliant, you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
• 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs
• Adjustable frequency PWM up to about 1.6 KHz
• 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
• Configurable push-pull or open-drain output
• Output enable pin to quickly disable all the outputs
• Terminal block for power input (or use the 0.1" breakout pins on the side)
• Reverse polarity protection on the terminal block input
• Green power-on LED
• 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header)
• Chainable design
• 220 Ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
• Solder jumpers for the 6 address select pins
• Fully assembled and tested

ProductSiteLaunchDate : 2019-04-10T11:11:25.397Z
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
UnspscCode : 32000000
Wattage : 1.4 kilowatts