Cart 2 india

Specification
Brand : RTELLIGENT
BulletPoint1 : Modbus stepper driver: 24 - 100VDC or 18 - 80VAC power supply, 7.0A output current peak. Run the Modbus protocol over the RS485 network for real-time control of the drivers and motors.
BulletPoint2 : It is a high-performance bus-controlled stepper motor driver with intelligent motion controller function and built-in S-shaped and deceleration instructions to set acceleration and deceleration independently.
BulletPoint3 : Low Noise: Based on advanced control algorithm, the motor driver can run with low noise and low vibration
BulletPoint4 : Application: This NT86 stepper motor driver can control almost all of 2 phase nema 34 stepper motors 86mm flange whose current is under 7.0A. Usually for production line, Li-on battery equipment, solar energy equipment, 3C electrical equipment, etc.
BulletPoint5 : Warranty: Our step driver CNC controller has 12 months warranty. CE, ISO Certificated
Color : Silver
CurrentRating : 1.3 amps
ExternallyAssignedProductIdentifier1 : 0791590889242
ExternallyAssignedProductIdentifier2 : 791590889242
Horsepower : 0.167 horsepower
ItemName : RTELLIGENT Stepper Driver RS485 Modbus RTU Protocol 2 Phase for Nema 23/24/34 Open Loop/Closed Loop Step Motor (NT86)
ItemPackageDimensions_Height : 27.686 centimeters
ItemPackageDimensions_Length : 37.592 centimeters
ItemPackageDimensions_Width : 27.432 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : electronic-component-motor-drives
Manufacturer : RTELLIGENT
Material : Copper
MinimumFrequency : 50 hertz
ModelName : gear
ModelNumber : VFD015EL43A
NumberOfItems : 1
PartNumber : VFD015EL43A
ProductDescription : Rtelligent NT60 is a MODBUS / RTU stepper motor with RS485 communication suitable for 4-wire 2-phase Nema 23/24 stepper motors with a flange of 57/60 mm and currents less than 5.0A.

Functions:
▶ Slave address setting: SW1-SW5,the five DIP switches, are used to set 32-bit DSP addresses in total. Please select the corresponding position according to the drive panel.
▶Baud rate setting: SW6-SW7, the two DIP switches, are used to select a total of 4 baud rates in total. The master and slave must be set to the same baud rate. Please selectthe corresponding position according to the drive panel.
▶Terminal matching resistor: sw8 is used to select whether the 120 ohm terminating resistor is valid, off is invalid, and on is valid.
▶Cn interface: 4 single input port, 2 output port.
▶Encoder interface: GND : Internal power supply output GND; +5 V : Internal power supply output 5V. When operating in the closed-loop mode, 5V power is supplied to the encoder. The maximum output current of this 5v signal should not exceed 150mA.IN2-, IN2+ : The differential input signal, the 5v level signal, can receive the pulse signal when the external pulse is open loop, and the quadrature encoder A phase signal in the closed loop mode. IN1-, IN1+ : Receives the quadrature encoder B-phase signal as the IN2 port.
▶ RJ45 interface: Network communication interface, also used to connect PC debugging software.
▶ Power and Motor interface V-, V+ is powered by DC power supply. 24 - 50V DC is recommended for the operating voltage range, the power supply is greater than 150W. A+, A-, B-, and B+ are respectively connected to the A and B phase windings of the two-phase motor.

Specifications:
▶ Debugging software interface: USB to 485
▶ Maximum current : 5A
▶ Dimension: 118*75.5*33mm
▶ Power supply : 24~50V DC; 36V or48V recommended.

Package Contents:
1 x ECR60 EtherCAT Stepper Driver
ProductSiteLaunchDate : 2020-06-12T07:00:00.000Z
Size : 1 Phase
Speed : 1800 rpm
Style : NT86
UnitCount : 1
UnspscCode : 26111500
Voltage : 115 volts