Cart 2 india

Specification
Brand : CNCdrive
BulletPoint1 : Replaces the standard parallel port interface.
BulletPoint2 : Operate a CNC machine over a USB connection
BulletPoint3 : Works seamlessly with Mach3 Software (sold separately).
BulletPoint4 : Pulses at rates up to 100 kHz.
BulletPoint5 : ★Rated Current: 8A, Max Current: 15A, Quiescent Current: 0.005A (Standby).
BulletPoint6 : Control the forward or reverse direction and the stop of DC motor by switch
CircuitType : 2-way
Color : Grey
CompatibleDevices : CNC machines and computers with parallel ports or parallel port emulation
ConnectivityProtocol : X-10
ConnectorType : Mini USB or USB Type B
CurrentRating : 20 milliamps
CustomerPackageType : Standard Packaging
ExternallyAssignedProductIdentifier1 : 738426125112
ExternallyAssignedProductIdentifier2 : 0738426125112
ExternallyAssignedProductIdentifier3 : 00024822090001
IncludedComponents : 无
InputVoltage : 5 volts
InternationalProtectionRating : 220 volt
ItemName : CNCdrive UC100 USB to Parallel CNC Motion Controller
ItemPackageDimensions_Height : 23.8 centimeters
ItemPackageDimensions_Length : 4.4 centimeters
ItemPackageDimensions_Width : 12.8 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : motor-speed-controllers
Manufacturer : CNCdrive
Material : Ceramic
ModelNumber : UC100
MountingType : Panel Mount
NumberOfItems : 1
NumberOfPorts : 1
OperatingTemperature : 25 degrees_celsius
OperatingVoltage : 220 volts
OperationMode : MANUAL-AUTOMATIC
PartNumber : UC100
ProductDescription : USB Motion Controller Automatic Firmware checking and Firmware update. Motion control on up to 6-axis (X, Y, Z, A, B, C). Configurable maximum stepping frequency, the options are 25kHz(with 20usec pulse length), 50kHz(with 10usec pulse length), 100kHz(with 5usec pulse length). 12 5Volt 20mA (TTL level) buffered outputs with current sink/source capability. 5 input pins with at 5V (TTL level) with Schmitt triggered filtered inputs internally pullup to 5Volts at 4.7kOhms. 100% LPT port compatible pinout. Does not include a DB25 gender changer, So if your breakout board has a female connector, you will need to add one of these gender changer: A19. Note that this device is not optically isolated and will make the grounds of the breakout board common with the grounds of the PC. Faulty wiring on the controller could allow a ground loop with the main power supply, which may cause damage to the UC100 or even the PC. Using this isolator board will protect your system: C83
ProductSiteLaunchDate : 2015-02-17T04:02:03.488Z
SpecificUsesForProduct : PC
StreetDate : 2017-08-21T00:00:01Z
Style : Wall Mount
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredDgHzRegulation1 : not_applicable
SupplierDeclaredDgHzRegulation2 : not_applicable
SupplierDeclaredDgHzRegulation3 : not_applicable
SupplierDeclaredDgHzRegulation4 : not_applicable
SupplierDeclaredDgHzRegulation5 : not_applicable
SwitchType : Dimmer Switch
TerminalType : Scr
UnitCount : 1
UnspscCode : 43202222
Voltage : 5 volts
Wattage : 10000 watts