Cart 2 india

Specification
Brand : SparkFun
BulletPoint1 : This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485.
BulletPoint2 : This Breakout Features: Fully equipped with SP3485 RS-485 transceiver and supporting components. Operates from a single +3.3V supply. Interoperable with +5.0V logic.
BulletPoint3 : Also Features: RS-485 input/output broken out to RJ-45 connector, 3.5mm screw terminal, and 0.1" pitch header. Driver/Receiver Enable connected to RTS line. -7V to +12V Common-Mode Input Voltage Range. Allows up to 32 transceivers on the serial bus. Driver Output Short-Circuit Protection. 0.9x1.0".
BulletPoint4 : The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply.
BulletPoint5 : This breakout board includes the SP3485 RS-485 transceiver, filter capacitor, and other components shown on the schematic. We've broken out the RS-485 output to three different connections: (1) an RJ-45 connector, (2) a 3-pin 3.55mm screw terminal, and (3) a 3-pin 0.1" pitch header; none of these output connectors come populated.
BulletPoint6 : Note: The module does not include cables, and requires the use of single-mode single-fiber LC-LC cables.
CompatibleDevices : Personal Computer
CompatibleDevices1 : Microcontroller
CompatibleDevices2 : Single Board Computer
CompatibleDevices3 : Raspberry Pi
CompatibleDevices4 : Arduino (with 3.3V or logic level converter)
ConnectivityTechnology : Ethernet
DataLinkProtocol : IEEE 802 11b
ExternallyAssignedProductIdentifier : 9115433151715
ExternallyAssignedProductIdentifier1 : 0845156004508
ExternallyAssignedProductIdentifier2 : 845156004508
HardwareInterface : 802_11_bgn
IncludedComponents : USB
ItemName : SparkFun Transceiver Breakout - RS-485 SP3485 Half-Duplex Transceiver Operates from a Single +3.3V Supply, Interoperable with +5.0V Logic
ItemPackageDimensions_Height : 4 millimeters
ItemPackageDimensions_Length : 34 millimeters
ItemPackageDimensions_Width : 54 millimeters
ItemTypeKeyword : network-transceivers
Manufacturer : SparkFun Electronics
MaximumSupplyVoltage : 12 volts_of_direct_current
MinimumSupplyVoltage : 9 volts
ModelName : BPI-R3
ModelNumber : BOB-10124
MountingType : Surface Mount
NumberOfChannels : 1
NumberOfItems : 1
OperatingSystem : Linux
OutputPower : 1585 milliwatts
PartNumber : BOB-10124
ProcessorCount : 1
ProductDescription : This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply. This breakout board includes the SP3485 RS-485 transceiver, filter capacitor, and other components shown on the schematic. We've broken out the RS-485 output to three different connections: (1) an RJ-45 connector, (2) a 3-pin 3.55mm screw terminal, and (3) a 3-pin 0.1" pitch header; none of these output connectors come populated.
ProductSiteLaunchDate : 2022-10-27T03:01:16.892Z
SpecificationMet : [Po] Potentially Fcc, Ce, Rohs
SupplierDeclaredDgHzRegulation : not_applicable
UnspscCode : 32101600
Voltage : 12 volts_of_direct_current
WarrantyDescription : 1 year
WirelessCommStandard : 802_11_BGN