Cart 2 india

Specification
Amperage : 20 amps
Brand : RACO
BulletPoint1 : Rugged welded design does not fall apart during construction.
BulletPoint2 : Available from one to six gang configurations in both 2-1/2" and 3-1/2" depths.
BulletPoint3 : Rectangular shape fits square cuts in block.
BulletPoint4 : Large volume design allows for additional work room inside the box.
BulletPoint5 : Standard 1/2" and 3/4" concentric knockouts.
BulletPoint6 : Device ears inside the box prevent mortar from getting in the device holes.
BulletPoint7 : Steel voltage partition #971 fits all 2-1/2" or 3-1/2" depths.
BulletPoint8 : Supplied with sixteen 1/2 and 3/4 in. concentric knockouts
Capacity : 31 cubic_inches
Color : Gray
CompatibleDevices : All
ConnectivityTechnology : USB
ConnectorType : USB
ExternallyAssignedProductIdentifier1 : 050169006962
ExternallyAssignedProductIdentifier2 : 0050169006962
ExternallyAssignedProductIdentifier3 : 00050169006962
ExternallyAssignedProductIdentifier4 : 0750762270615
ExternallyAssignedProductIdentifier5 : 00750762270615
FinishType : Powder Coated
IncludedComponents : under-counter-light-mounting-accessories
InstallationType : Screw-In
ItemName : Raco Hubbell 696 Masonry Boxes, 3-1/2 in. Deep - Nongangable with Conduit KO's, 2-Gang, 3-25/32 in. Wide, Gray
ItemPackageDimensions_Height : 9.6012 centimeters
ItemPackageDimensions_Length : 8.89 centimeters
ItemPackageDimensions_Width : 9.4996 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : electrical-outlet-boxes
Manufacturer : RACO
Material : Alloy Steel
ModelNumber : 696
NumberOfItems : 1
PackageLevel : unit
PartNumber : 696
PowerPlugType : no_plug
ProductDescription : INSTALLATION STEP:
1. Prior to installation, a professional granite cutter should cut a square hole in the desired location of the receptacle, the size of the hole is 4-1/16" X 4-1/16"
2. Always use the supplied steel box, for the floor installation, secure the steel box on the bottom of the hole by the two screws provided. If you install on the countertop, it is necessary to install the tab provided to the steel box, then use the construction adhesive or glue to attach the steel box to the countertop.
3. Run wire into the 1/2" knock out the side of the box furthest away from the front of the countertop, if the knockouts are used closest to the front of the counter, the unit will not open because of interference.
Note: For the countertop installation, the steel box should be placed at the back of countertop. 4. Only use 9 or 10 gauge stranded U.L.listed wire, strip the wires and insert the stripped wire into the quick connect terminal box making sure that no striped wire is exposed, tighten the screws to secure the wires to the terminal block.
Note: Any excess wires should be pushed out of the box or made to be as flat as possible on the bottom of the steel box. Failure to push the wires out of the box or make it flat in the box will interfere with the opening mechanism and the unit will not be able to pop open.
5. Pop up the receptacle and line up the two screw holes with the thread holes in the steel box and then fasten by 2 screws provided.
6.Open and close the unit: Pulling the opening tab until the outlet completely open and close to the its lock place.
ProductSiteLaunchDate : 2005-01-27T00:00:01-00:00
Size : 2-Gang
SpecificationMet : Ul
Style : Compact
SupplierDeclaredDgHzRegulation : unknown
TotalPowerOutlets : 2
UnitCount : 1
UnspscCode : 39121300
Voltage : 125 volts