Cart 2 india

Specification
Brand : Podazz
BulletPoint1 : Podazz IR Sensor Module utilizes a slot photoelectric sensor consisting of an IR LED and an NPN phototransistor in a 5.9 mm wide slot.
BulletPoint2 : As soon as a non-transparent object passes through the slot, the IR Sensor Module triggers a low TTL level output.
BulletPoint3 : Dither pulses are very stable using Schmitt triggers and can be used for small vehicle speed measurement, distance measurement and other applications.
BulletPoint4 : Mounting holes on both ends with M3 screws.
BulletPoint5 : Operating voltage: 3.3V-5V, output form: digital switching output (0 and 1)
BulletPoint6 : PIN DEFINITION: VCC is connected to the positive pole of the power supply, GND is connected to the negative pole of the power supply, OUT switch signal output.
BulletPoint7 : PRODUCTS INCLUDE: 5 x Correlation Photoelectric Sensor;5 x Encoders;15 x Male and female cable.
CenterlineLength : 7 centimeters
CircuitBreakerType : Standard
Color : Yellow
ConnectorType : Screw
CurrentRating : 300 milliamps
ExternallyAssignedProductIdentifier : 7352918842252
GpsrSafetyAttestation : 1
IncludedComponents : 5 x Sensor;5 x Encoders;15 x Male and female cable
ItemName : Podazz 10PCS IR Sensor Module, Velocimetry Sensor Module, Optical Interrupter Sensor, Slotted Optical Optocoupler, Motor Speed Detection, for Robot Arduino
ItemPackageDimensions_Height : 0.83 inches
ItemPackageDimensions_Length : 5.63 inches
ItemPackageDimensions_Width : 4.13 inches
ItemPackageQuantity : 1
ItemTypeKeyword : electronic-component-photoelectric-sensors
Manufacturer : Podazz
Material : Plastic
ModelNumber : ELE303
MountingType : Panel Mount
NumberOfContacts : 3
NumberOfItems : 1
NumberOfPoles : 2
NumberOfPositions : 2
PartNumber : IR Sensor Module
ProductDescription :

Product Usage:

✔+5 is the positive input port of the power supply, which can be connected to a voltage of 3.3V~5V.

✔GND is the negative input port of the power supply. OUT is the signal output port, which is connected to the I/O port of the microcomputer. Generally, it is connected to the external interrupt.

✔For other master boards or higher level master boards (such as Arm), if you need to set the I/O port to input/output mode, you must set it to input mode/receive mode, otherwise it can'T be used. 51 series microcontrollers can be used directly without setting input and output modes.

Product Features:

Module adopts groove to light sensor. It consists of infrared light-emitting diode and NPN photoelectric triode. The width of the groove is 5.9mm. The non-transparent object can be triggered through the slot type, the output TTL is low.

Instructions for Use:

1. After connecting the VCC and GND, the module signal indicator will be on. When there is no obstruction in the module slot, the receiving tube is turned on, and the module out outputs high level. During the cover, OUT outputs a low level and the signal indicator is destroyed.

2. Module OUT can be connected to the relay, forming functions such as limited switch, and can also be connected to the active bee lumator module to form alarm.

3. OUT output interface can be directly connected to the single -chip machine IO port. Generally, it is interrupted and detects whether the sensor is obstructed. If the motor code disk is used, the motor can detect the speed of the motor.

#Caution: Do not reverse the positive and negative terminals to avoid burning the electronic components on the board. Players should set the I/O port of MCU to input mode/receive mode, otherwise it cannot be used. For Arduino players, the I/O port of MCU must be    set to input mode/receive mode, otherwise it cannot be used.ProductSiteLaunchDate : 2024-06-25T06:04:29.731Z
SensingMethod : Diffuse
SpecificationMet : Ma
SupplierDeclaredDgHzRegulation : not_applicable
UnspscCode : 46171600
Voltage : 24 volts