YJYGR 2000W 50A ZVS Induction Heating Board Heater Module Flyback Driver Heater Dissipation Coil Dual Fan with Copper Tube

Customer rating 4.6 stars

Imported from USA | Ships in 10 working days

5% additional discount on UPI | Cash On Delivery available

1

₹31080 -35% ₹20200/-

The price at cart2india.com is inclusive of custom duties, GST, freight forwarding and other charges.

Free Shipping across India. Powered by BlueDart

Product Information


Specification
Brand : YJYGR
BulletPoint1 : Package comes with heating circle diameter is 60 mm, design voltage is 36V, if you use more than 40 voltage power supply shall be used for inner diameter 70 mm above diameter heating ring, water pump use 12V dc power supply, please use separate power supply voltage regulator module to avoid burn out fan and water pump.If you find that the MOS tube fever, then the first thing to consider whether the power output meets the requirements.
BulletPoint2 : You must pay attention to when using switch power supply,because the high-power switching power supply usually have soft start function,namely the output voltage is slowly rising,and if the voltage rise to 10V before connected induction heating circuit will be caused by lacking voltage lead to circuit can't afford to vibrate,so the two MOS tube conduction and burned components at the same time,so be sure to switch the power supply voltage stability and then access the induction heating circuit.
BulletPoint3 : Note:The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. The buyer can prepare water cooling system separately, can buy a small water pump and 2 meters of inner diameter of 4mm rubber hose.
BulletPoint4 : When heating the metal objects do not to heat too large metal, otherwise it may be overloaded with power, please add a 35A fuse or ammeter and air switch will be better. (package does not inclues).Although this drive plate can withstand more than 40A current, but it is recommended that not exceed 48V 35A to prevent accidents and damage.Do not empty the board, otherwise it will issue a very high frequency of noise, and then MOS tube will burn out
BulletPoint5 : The minimum input voltage of the module is 12V, it doesn't mean all the 12V power supply can be used, some novice buyers may use a smaller power supply. This module has specific voltage and current requirements, the voltage 12V current must be more than 10A power supply can be used, if the power is too low will lead to the power output is greatly reduced, when the voltage is lower than 12V, it will lead to two MOS at the same time conduction, will burn MOS tube;
CurrentRating : 10 amps
ExternallyAssignedProductIdentifier : 8691415899581
ItemName : YJYGR 2000W 50A ZVS Induction Heating Board Heater Module Flyback Driver Heater Dissipation Coil Dual Fan with Copper Tube
ItemPackageQuantity : 1
ItemTypeKeyword : printer-memory
Manufacturer : YJYGR
Material : Metal
MaximumRotationalSpeed : 3500 rpm
MaximumSwitchingCurrent : 10 amps
NoiseLevel : 28 decibels
NumberOfItems : 1
PartNumber : 652573979
PowerConnectorType : 2-Pin
ProductDescription : Induction heating is recommended to use 36V 20A power supply, 12V power supply is too small heating almost no response, and 12V power supply easily lead to the power supply output voltage decreases, below 12V is very dangerous

Induction heating power is great, so fever is normal, be sure to do a good job of cooling.

Induction heating, the power recommended more than 48V 50A switching power supply. More than 24V power supply, then more than 20A power supply, the greater the voltage, the greater the current, the greater the heating power, heating faster.

This products maximum power 2000W, adopted super PCB layout design and super heat sink, heat dissipation good, since with a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc.

This induction heating circuit uses 12-48V low voltage DC power supply, maximum current 40A, the most highest power is 2000W. It can work continuously under the condition of good heat dissipation.

Due to its moderate power, it can be used by DIY players to give smaller players the parts can be treated by quenching, annealing and other heat treatment. You can also be melted with graphite crucible Kim, Silver, Copper, aluminum and other metal, heating evenly, is fast and very convenient.

Size: 240*120mm

colour:black

Material:metal

Package Contents:

1 * 2000W ZVS heating plate

Only the above package content, other products are not included.

Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
ProductSiteLaunchDate : 2021-08-31T02:19:17.339Z
Style : Simple
UnspscCode : 52140000
Voltage : 12 volts

Questions & Answers

Have a question? Ask experts

?
No question found

Ratings & Review

Rating Breakdown (average)

5*
6
4*
2
3*
1
2*
0
1*
0

Read all 9 customer reviews

IÕm extremely impressed with this item.

Totally worth every penny.

Very functional and easy to use.

Feels premium and well-crafted.

High quality and great value.

Expected a bit more for the price.

High quality and great value.

CanÕt believe how great this is.

Good product with reliable performance.

Have an opinion on this page? Let's hear it.