Cart 2 india

Specification
Brand : Radiolink
BulletPoint1 : Radiolink Antennas for R6DS R6DSM R12DSM 6CH 10CH 12CH Receiver Antennas AT9 AT9S AT10 AT10II Transmitter with Connector
BulletPoint2 : Length: about 9cm
BulletPoint3 : Radiolink R6DS 2.4G Six Channel Receiver, using DSSS&FHSS double spread spectrum anti-jamming technology, suitable for Radiolink transmitters AT9, AT9S and AT10.
BulletPoint4 : Radiolink R6DSM 2.4G 10 Channel Receiver, using DSSS and FHSS double spread spectrum anti-jamming technology, applicable to Radiolink 9 channel remote control AT9, AT9S; Radiolink 10 channel remote control AT10, AT10II, 1g extremely light weight, the best partner through the machine.
BulletPoint5 : Radiolink R12DSM 2.4G 12 Channel Receiver, using DSSS and FHSS double spread spectrum anti-jamming technology, applicable to Radiolink 10 channel remote control AT9, AT9S; Radiolink 12 channel remote control AT10, AT10II.
Color : Red/Black
ExternallyAssignedProductIdentifier1 : 0712804879736
ExternallyAssignedProductIdentifier2 : 712804879736
Impedance : 50 ohm
ItemName : Radiolink Antennas for R6DS R6DSM R12DSM 6CH 10CH 12CH Receiver Antennas AT9 AT9S AT10 AT10II Transmitter with Connector
ItemPackageDimensions_Height : 13.97 centimeters
ItemPackageDimensions_Length : 4.318 centimeters
ItemPackageDimensions_Width : 9.398 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : hobby-rc-vehicle-antennas
Manufacturer : Radiolink
Material : ABS
ModelName : FBA_4330951994
ModelNumber : FBA_4330951994
NumberOfChannels : 9
NumberOfItems : 1
PartNumber : M23804
PowerSourceType : Battery-Powered
ProductDescription : Radiolink Antennas for R6DS R6DSM R12DSM 6CH 10CH 12CH Receiver Antennas AT9 AT9S AT10 AT10II Transmitter with Connector
Support S-BUS (9 channels)

Receiver antenna installation:

1. Try to ensure that the antenna is straight, otherwise it will reduce the effective control range.
2. Large model machines may have metallic components that affect signal transmission. In this case, the antenna should be on both sides of the model. This maintains the best signal state in any flight attitude.
3. The antenna should be as far away from metal conductors and carbon fibers as possible, at least half an inch away, but not excessively bent.
4. Keep antennas as far away as possible from motors, electronic governors (ESC) and other possible sources of interference. In the actual installation of the receiver, it is possible to use a sponge or foam to wind it up for shock protection.
5. The receiver contains some high-precision electronic components. Therefore, when using, please be careful to prevent violent vibration or in a high temperature environment.
6. To better protect the receiver, use a shock-proof material such as R/C special foam or rubber cloth to wind it. To prevent the receiver from getting wet, it is best to put it in a plastic bag and seal it. If moisture enters the receiver, it may cause intermittent out-of-control or even complete loss of control. Placing the receiver in a plastic bag also prevents fuel and debris from entering the body.

Warning: After the connection program is completed, please turn off the transmitter and then turn it on. Then the program takes effect to confirm that the receiver is indeed connected to the transmitter and controlled by the transmitter. Do not perform connection procedures when the motor's power wires are connected to the governor or when the engine is in operation. In this case, serious injury may occur.

ProductSiteLaunchDate : 2018-03-29T07:00:00.000Z
Style : White RP-SMA
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredDgHzRegulation1 : not_applicable
SupplierDeclaredDgHzRegulation2 : not_applicable
SupplierDeclaredDgHzRegulation3 : not_applicable
SupplierDeclaredDgHzRegulation4 : not_applicable
SupplierDeclaredDgHzRegulation5 : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
UnspscCode : 43221700
WarrantyDescription : 1 year manufacturer