Cart 2 india

Specification
Brand : YukaBa
BulletPoint1 : EQUIPPED WITH 10,000 RPM MAX. Fits Shiandaiwa T195S T220 T222 T230 T230s T231 T242 T242X T2510 T2510X 22T C230 C242 C2510
BulletPoint2 : HOW TO RERESTING: You don’t take it apart. You spin it until the arrow lines up with the hole. Then you just feed about ten feet of line on each side and spin it. It spools up as you spin. If you have leftover line inside the spool you will need to take the unit off to empty the line. You are supposed to be able to press-in the panels on the side enough to clear the retaining ledge to free the top of the unit to pull out the spool (you have to do this on both sides)
BulletPoint3 : Replaces Echo Speed Feed 400
BulletPoint4 : Usend On ECHO PAS210 PAS211 PAS225 PAS225VP PAS225VPB PAS230 PAS231 PAS260 PAS261 PAS265 PAS266 PAS280 PAS2100 PAS2400 PAS2601 power source attachment
BulletPoint5 : Trimmer Head Diameter: 3-3/4"
Color : 1 Pack
CuttingWidth : 1 inches
ExternallyAssignedProductIdentifier : 7505312940745
ExternallyAssignedProductIdentifier1 : 713325063178
ExternallyAssignedProductIdentifier2 : 0713325063178
ItemName : YukaBa Head for Echo Speed Feed 400 SRM-225 SRM-230 SRM-210 Echo Weed Eater Pas210 Pas211 Pas225 (1 Pack)
ItemPackageDimensions_Height : 19.05 centimeters
ItemPackageDimensions_Length : 6.7056 centimeters
ItemPackageDimensions_Width : 17.78 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : string-trimmer-replacement-parts
ItemTypeName : Head for Echo Speed Feed
Manufacturer : YukaBa
ModelName : YukaBa
ModelNumber : HEAD01
NumberOfBoxes : 1
NumberOfItems : 1
PartNumber : HEAD01
PowerSourceType : NO
ProductDescription :

Used on Shiandaiwa T195S T220 T222 T230 T230s T231 T242 T242X T2510 T2510X 22T C230 C242 C2510
Fit for Echo PAS210 PAS211 PAS225 PAS225VP PAS225VPB PAS230 PAS231 PAS260 PAS261 PAS265 PAS266 PAS280 PAS2100 PAS2400 PAS2601 power source attachment
For Echo Straight shaft trimmer SRM140 SRM200 SRM202 SRM210 SRM230 SRM250 SRM251 SRM260 SRM261 SRM265 SRM266 SRM266S SRM266T SRM266U

HOW TO RERESTING:

You don’t take it apart. You spin it until the arrow lines up with the hole. Then you just feed about ten feet of line on each side and spin it. It spools up as you spin. If you have leftover line inside the spool you will need to take the unit off to empty the line. You are supposed to be able to press- in the panels on the side enough to clear the retaining ledge to free the top of the unit to pull out the spool (you have to do this on both sides)

If you have leftover line inside the spool you will need to take the unit off to empty the line. You are supposed to be able to press-in the panels on the side enough to clear the retaining ledge to free the top of the unit to pull out the spool (you have to do this on both sides). I could not press the side panels in enough to free up the top piece. So I used a flat head screwdriver from the top going down into the ledge area to leverage out the panel from the retaining ledge. This worked fine. Then you just put it all back together and line up the line-holes on the sides to where you can see through the unit to the other side. To do this you hold the bottom of the unit and turn the top part (with the holes). Then you run about 10-12 feet of line through the holes (5-6 feet extending on each side). Then hold the bottom piece and turn the top to load the line onto the spool.

Size : 1 Pack
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
UnitCount : 1