Cart 2 india

Specification
AgeRangeDescription : Adult
ArtCraftKitType : WATER_TRANSFER_PRINTING_KIT
Brand : Generic
BulletPoint1 : 50cm width, 1unit is 400cm length, 2units=800cm continuous length in a roll, and so on...
BulletPoint2 : Suitable for White/Silver base color
BulletPoint3 : Applicable with all brands of activators
BulletPoint4 : Sealed packing to keep the film in good condition
BulletPoint5 : Sealing clip included for your film preservation
Color : Black
ExternallyAssignedProductIdentifier1 : 0641606676383
ExternallyAssignedProductIdentifier2 : 641606676383
IncludedComponents : Water Transfer Printing Film, Activator (not specified), Sealing Clip, Scissors, Tape, Spray Bottle, Instructions
ItemName : ST Color Carbon004-Water Transfer Printing / Hydrographics / Hydro Dipping Film-Streamline Carbon Fiber(Black Stripe)-50cm Widthx400cm Length
ItemPackageDimensions_Height : 52.7812 centimeters
ItemPackageDimensions_Length : 2.5908 centimeters
ItemPackageDimensions_Width : 3.2004 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : screen-printing-kits
Manufacturer : UniJade
Material : PVA
Material1 : Wood
Material2 : Plastic
ModelName : Carbon Fiber
ModelNumber : Carbon004
NumberOfBoxes : 1
NumberOfItems : 1
NumberOfPieces : 1
PaintType : oil-based
PartNumber : Carbon004
ProductDescription : Water Transfer Printing/Hydro Dipping/Hrdrographics is the technique to transfer the pattern of the film to any object surface. Please follow the steps 1. Prep, Prime, and Paint your object. Besides of ABS plastic, all other materials need to be painted with oil base paint in order to proceed water transfer printing. 2. Cut the film in proper size for your object It's important to consider the height of your object. Make sure the film is much bigger than the cover area of your object. 3. Tape 4 sides of the film In case of the pattern distortion and scattering after spraying activator. 4. Distinguish the hydrophilic side of the film We and use your thumb and index fingers to pinch the film for few seconds. After released, the sticking side is the hydrophilic side of the film. 5. Lay the film on water for more than 1min WITH the hydrophilic side face down Tap/drive the bubble out under the film if there is any. The lower water temperature is, the more time required for the film stay on water. 6. Spray activator in fine mist form evenly on the film to activate the film 7. Dip your object in 40degree angle into water slowly and steadly 8. After fully immersed, slightly shake your object in the water for few seconds 9. Take out your object and rinse the object surface with running water of faucet or showerhead It's important not to touch or rub the object surface before it's dry during/after rinsing. 10. Let the object dry naturally or by oven 11. Paint the clear paint for glossing and/or protection purpose for your object surface
ProductSiteLaunchDate : 2021-05-19T20:00:33.503Z
Seasons : All Seasons
Size : 50cm Widthx400cm Length
Style : Carbon Fiber
SubjectCharacter : Skulls
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredDgHzRegulation1 : not_applicable
SupplierDeclaredDgHzRegulation2 : not_applicable
SupplierDeclaredDgHzRegulation3 : not_applicable
SupplierDeclaredDgHzRegulation4 : not_applicable
SupplierDeclaredDgHzRegulation5 : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
TargetAudienceKeyword : People
TargetAudienceKeyword1 : women
TargetAudienceKeyword2 : unisex-adult
TargetAudienceKeyword3 : teens
TargetAudienceKeyword4 : DIY hobyy
TargetAudienceKeyword5 : craftsmanship
TargetGender : unisex
Theme : Carbon Fiber
UnspscCode : 44102000
WarrantyDescription : FBA return policy