Cart 2 india

Specification
Brand : SZSEVSIOT
BulletPoint1 : 【Compatibility】Dedicated to the latest single-board computer the Raspberry Pi 5, compatible with Raspberry Pi 5 8GB / 4GB / 2GB / 1GB .
BulletPoint2 : 【Easy and Quick M.2 Disk Installation】Support M.2 KEY-M NVMe SSD 2230/2242 length , quick installation of M.2 disks in 2230 or 2242 format.
BulletPoint3 : 【Dual LED Indicators】Features 2 LED lights for power supply voltage (“PWR”) and M.2 disk activity (“ACT”).
BulletPoint4 : 【Stackable Design】Supports the standard 40-pin Raspberry Pi HAT connector,allows for further connection of additional HAT boards in a stack.
BulletPoint5 : 【Packing List】1 x NVPI5-2242T board,2 x PCIe FFC cable (30mm length),2 x PCIe FFC cable (60mm length),4 x M2.5x14mm F/F Spacers,4 x M2.5x6+6mm F/M Spacers,1x 40-pin male-female HAT connector，1x Screws Pack Accessories.
Color : 2242T
CompatibleDevices : Raspberry Pi 5
ConnectivityTechnology : 40-pin Raspberry Pi HAT connector
CoolingMethod : Copper Heatsinks
CustomerPackageType : Standard Packaging
ExternallyAssignedProductIdentifier1 : 774034299661
ExternallyAssignedProductIdentifier2 : 0774034299661
IncludedComponents : 1 x NVPI5-2242T board
ItemName : NVMe (M.2 M-Key 2230, 2242 PCIe Gen3) SSD HAT for Raspberry Pi 5,NVMe HAT PCB with M.2 Slot (M-Key)
ItemPackageDimensions_Height : 17.6022 centimeters
ItemPackageDimensions_Length : 1.2954 centimeters
ItemPackageDimensions_Width : 10.6934 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : single-board-computers
Manufacturer : Seven Senses IOT
Material : Metal
MemoryStorageCapacity : 4 MB
ModelName : Raspberry Pi 5
ModelNumber : 2242T
NumberOfItems : 1
OperatingSystem : Linux
PartNumber : 2242T
ProcessorCount : 1
ProductDescription :

Features:

• Compatible with other HAT shield
• Support boot from the NVMe drive
• 30mm length Flat Flex Cable
• Supports installation of official active coolers
• Dual LED Indicators: “PWR” and “ACT”
• Supports 2230/2242 NVME M2 SSD only
•  40-Pin Raspberry Pi HAT Connector Support
• M.2 Standard-Compliant Power System

 

Gettingstarted

Firmware

Make sure your Raspberry Pi 5 firmware is up to date with the 2023-12-06 or later version. Software update on the RPi OS should do this for you, but you canforce it by running sudorpi-eeprom-update in the Terminal.

If you have updated your firmware and want to boot from the NVMe drive, you might have to get technical and run sudo rpi-eeprom-config --edit from the Terminal and change the BOOT_ORDER to be 0x416 instead of 0x41.

To enable experimental and not-officially-supported PCIe 3 mode, add the follow lineto the [all] section at the end of your Raspberry Pi /boot/config.txt file like this:

 

# Enable the PCIe external connector

dtparam=pciex1

# Force Gen 3.0speeds

dtparam=pciex1_gen=3

 

Bootingfrom NVMe

If you want to boot from the NVMe drive follow these extra steps:

1. Format the drive using Raspberry Pi Imager
2. Shutdown
3. Remove your microSD card
4. Power back on

Notes

• Always power off your RPi and disconnect the power supply before installing or uninstalling the NVPI5-2242T and NVPI5-2280B;
• NVPI5-2242T and NVPI5-2280B offers a general purpose PCIe x1 connection;
• We do not recommend WD Green SSDs at this time. Drives such as the SN350 are temperamental with the CM4 and RPi 5.

ProductSiteLaunchDate : 2024-01-09T09:08:46.455Z
RecommendedUsesForProduct : DIY Projects
Size : 2242T
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
TotalUsbPorts : 2
UnspscCode : 43201830
WarrantyDescription : 1 year manufacturer
WirelessCommStandard : 802_11_N