Cart 2 india

Specification
Brand : DIMATTEO
BulletPoint1 : Dimatteo 73 pcs Fishing Sinker Mould: fishing swimbait jighead mold kits 7g 10g 14g 18g 4 cavities
BulletPoint2 : Making Professional Bank Sinker at Home: With this product, you can make professional bank sinker at home
BulletPoint3 : Provide a Money Saving Solution for Fishing Enthusiasts: Long term purchase of this type of bank sinker will cost a lot of money, and this sinker mold provides consumers with a better choice. you can make a large number of cheap bank sinker at home for a long time
BulletPoint4 : Easy to Use: This mold is easy to use for both novice and experienced fishing enthusiasts, and can help you easily make professional bank sinker
BulletPoint5 : Handmade DIY: You can enjoy the fun of DIY while making bank sinker, feel the sense of achievement brought by making bank sinker, and bring a different fishing experience to you
Color : silvery
ExternallyAssignedProductIdentifier1 : 614161044485
ExternallyAssignedProductIdentifier2 : 0614161044485
ExternallyAssignedProductIdentifier3 : 00047708703390
FishingTechnique : DIY
GpsrSafetyAttestation : 1
ImportDesignation : Imported
IncludedComponents : Aluminum
ItemName : Dimatteo 73 pcs Fishing Swimbait Jighead Mold Kits 7g 10g 14g 18g 4 Cavities
ItemPackageDimensions_Height : 32.1056 centimeters
ItemPackageDimensions_Length : 6.4008 centimeters
ItemPackageDimensions_Width : 15.3924 centimeters
ItemPackageQuantity : 1
ItemShape : Drop
ItemTypeKeyword : fishing-sinkers-and-weights
Manufacturer : Dimatteo
Material : Aluminum
Material1 : Blend
Material2 : Blend
Material3 : Blend
Material4 : Blend
Material5 : Blend
ModelName : JIG 003
ModelNumber : Do it Mold 1101 BK-8-A
NumberOfItems : 1
NumberOfPieces : 73
PackageLevel : unit
PartNumber : CZ-UTQC-G1PC
ProductDescription : How to make sinkers: 1. Ensure you are wearing protective clothing and all care must be taken when heating and pouring lead. 2. Put scrap lead into saucepan and heat until molten (lead will normally melt at 650 degrees). 3. Once lead is molten use a cooking spoon to take away any impurities that have risen to the top. 4. Take your coat hanger wire (wire is only used when making sinkers that require a hole in the centre) and place within the mould. 5. Using the tongs grab tour mould carefully and have the pouring cavity facing you. 6. Pour molten lead into mould until cavity is full. 7. It is recommended the mould be preheated before use. 8. Once mould has been heated up and your lesd is fully molten and clean you can proceed to pour the lead in to the cavity. 9. Wait 10 seconds and using pliers pull wire out then proceed to open mould. 10. Using your pliers snip the excess lead of the top of the sinkers. 11. Good luck and remember to always take care. 12.When disposing of unwanted lead please take note of your local authority about appropriate methods. Warning: 1. Lead is a toxic material 2. Use PPE when handing moulds 3. Use dry moulds as water can cause molten lead to explode
ProductSiteLaunchDate : 2022-11-08T08:25:17.944Z
RecommendedUsesForProduct : making fishing sinkers
Size : 26x20x3cm
SupplierDeclaredDgHzRegulation : not_applicable
UnspscCode : 49131500
WarrantyDescription : 1 Year Warranty Against Manufacturer Defects