Cart 2 india

Specification
AgeRangeDescription : adult
Brand : KYHHL
BulletPoint1 : We have a warehouse in the local area that can deliver accessories to you faster (this product is not made in China). Thank you for choosing us
BulletPoint2 : Description: Product includs: 3-Rubber Paddle 3-Metal Straps 9-Bolts & Lock Nuts 3-Self-tapping Screws;
BulletPoint3 : Rubber Paddle 1/4" thick(2"W x 5"L), Made from Styrene Butadiene rubber (SBR rubber) ,SBR rubber with minimum tensile strength of 725 PSI (5 MPA),Hard rubber with a durometer of 65-75; Metal Strap with holes - 1 3/8" W x 3 3/4"L , 1/16" thick Bolts (5/16-18 x 1 in. coarse thread) w/ 5/16-18 lock nuts (use 1/2" wrench & socket) ; Hex Bolts,Hex lock nuts nylon inser,self-tapping screw (#14 x 1),Sheet metal screw, Hex washer head self drilling.
BulletPoint4 : (Doesn't fit Ariens with curved impellers)
BulletPoint5 : This kit is to reduce the existing“gap”between the snow blower's impeller blades and the impeller chamber wall. The smaller the gap, the greater your machine's operational efficiency and snow throwing capability will be, and the less likely that your machine will clog up with snow.
BulletPoint6 : This "gap" allows snow and slush to slip by the blades and build up around the impeller and in the discharge chute clogging it. This gap also decreases the efficiency of the impeller's ability to propel the snow up the chute resulting in less throwing distance. This problem is well known to people with two-stage snow blowers, and the easy and the quick, inexpensive fix is to modify the impeller blades by adding a strip of reinforced rubber to each one of them to eliminate this gap.
BulletPoint7 : It is HIGHLY recommended that you install one kit on each blade however, because only modifying some but not all of the blades will cause a harmonic imbalance in the spinning impeller which could easily cause excessive wear on the impeller shaft bearing resulting in very costly repairs!
BulletPoint8 : If you have a single-stage snow blower, or your gap is less than 1/4" or greater than 5/8", you probably don't need or can't use this fix. Depending on how handy you are, this kit can be installed in 1-2 hours without too much difficulty!
BulletPoint9 : NOTE: If the gap varies around the chamber wall, you MUST install the rubber to fit the spot where the gap is the smallest, otherwise, the rubber will fail! The rubber paddles mounted should be installed so they are barely touching. Remember, ANY decrease in the gap between the impeller blades and the chamber wall will result in a significant improvement in operational efficiency and throwing distance!
Color : Assorted Color
ExternallyAssignedProductIdentifier : 7504597179819
ExternallyAssignedProductIdentifier1 : 0765037770806
ExternallyAssignedProductIdentifier2 : 765037770806
FinishType : Finish
IncludedComponents : inc
IsAssemblyRequired : 1
ItemDisplayDimensions_Height : 0.54 inches
ItemDisplayDimensions_Length : 1.64 inches
ItemDisplayDimensions_Width : 0.54 inches
ItemDisplayWeight : 0.3 pounds
ItemName : 3 Sets Universal 1/4" Blade Impeller Kit for 2 Stage Machine Snowblower
ItemPackageDimensions_Height : 0.79 inches
ItemPackageDimensions_Length : 3.94 inches
ItemPackageDimensions_Width : 2.76 inches
ItemPackageQuantity : 1
ItemShape : Rectangular
ItemTypeKeyword : snow-blower-accessories
Manufacturer : KYHHL
Material : Stainless steel
ModelName : 1/4" Blade Impeller Kit
ModelNumber : 1/4" Blade Impeller Kit
NumberOfBoxes : 1
NumberOfItems : 1
PartNumber : 765037770806
PowerSourceType : PowerSource
ProductDescription : 1/4" Blade Impeller Kit
ProductSiteLaunchDate : 2023-12-30T11:27:15.620Z
Size : 4.77X1.38X1.38CM
Style : Modern
SupplierDeclaredDgHzRegulation : not_applicable
UnitCount : 0.0353
UnspscCode : 22100000