Cart 2 india

Specification
Brand : Yosoo
BulletPoint1 : [Versatile temperature control] Choose between cooling or heating mode for flexible temperature regulation.
BulletPoint2 : [First Security] Establish upper and lower temperature limits to avoid accidents and guarantee a environment.
BulletPoint3 : [Automatic Temperature Maintenance] Continuously adjust cooling or heating for constant temperature control without manual intervention.
BulletPoint4 : [Precise temperature settings] Easily calibrate the temperature to meet its exact requirements and guarantee .
BulletPoint5 : [Easy to use] the LED screen and intuitive controls make the temperature configuration and monitoring very easy.
Color : #-01
ItemName : W3230 Switch Sensor Meter Thermostat Digital Temperature LED Temperature for Cooling in The Home, (12V red and Blue Display)
ItemPackageDimensions_Height : 3 centimeters
ItemPackageDimensions_Length : 8 centimeters
ItemPackageDimensions_Width : 4 centimeters
ItemTypeKeyword : temperature-controllers
Manufacturer : Yosoo
ModelName : Yosoosdgipr62no-01
ModelNumber : Yosoosdgipr62no-01
ProductDescription : 1. New quality and high.
2. You can select the cooling or heating work mode.
3. Establish the highest/ highest upper limit temperature to avoid accidents.
4. automatically begin to cool or heat at constant temperature.
5. Temperature calibration, can calibrate the temperature according to the requirement.

Speculation:
Characteristics:
New and of.
You can select the cooling or heating work mode.
Set the highest/ lowest upper limit temperature to avoid accidents.
Automatically begin to cool or heat at constant temperature.
Temperature calibration, can calibrate the temperature according to the requirement.
High temperature alarm, when the measurement temperature reaches the configuration temperature, the controller will be alarmed.
Budget:
Material: Electronic
Voltage: 12V /24V /110-220V (optional) (optional)
Power: 120/240/1500W (optional)
Weight: approximately 48g/1.7 oz
Packaging list:
1 x digital thermostat temperature alarm controller sensor
Circuit connection: See the circuit diagram to connect the power supply and load. At this time, the digital tube (upper) shows the real measured temperature value, and the digital tube (lower) shows the pre -established temperature. If the temperature sensor is missing or damaged, the digital tube will be shown \ "-\", and the buyer must verify if the temperature sensor is installed before using it.
The temperature control output is a 10A relay, which can meet several high power loads. Make sure the circuit is correct.
Indicator light, digital tube state:
Indicator light: off means that the relay is disconnected and means that the relay is closed
Digital tube: screen \ "-\",
1. Check if the temperature sensor is missing or damaged
2. High temperature protection of the heating mode
3. Low temperature protection in refrigeration mode
The relay in protection mode is automatically disconnected.
Use of keys: The thermostat panel has three keys, keys + keys - set keys
Key +: rapid accumulation of values
Key -: To achieve rapid decrease in value
Press restart: restart the button
Configuration key
Establish: Perform the configuration temperature configuration interface and the two -layer interface parameter configuration interface
Establish the digital short pressure tube (below) to establish the temperature quickly. Predetermined value - 20 ℃ and 0 ℃, 20 ℃ and 40 ℃, 60 ℃, 80 ℃, 100 ℃ and another convenient data set called quick user. For example: users must establish 68.8 ℃, first press briefly established in 60 ℃ and then through the buttons and fine adjustment at the corresponding temperature. After configuring, wait 5S to automatically store the data in memory. Compared to the first thermostat generation, the second generation is more convenient and flexible to operate, and the dual LED screen of the real temperature and the established temperature is more convenient to observe.
Press Long Set to enter the parameter configuration interface. P0-P5 is the corresponding parameter configuration . In the parameter configuration menu, a short press set can be used to change P0-P5. To modify a parameter, simply change the corresponding and confuse it by adding or subtracting keys. Press Long press to save data after configuration, or wait 6S to save data automatically.
Reminder:
The P3 1 configuration means that the thermostat will stop working for 1 minute, and press long configured to activate again.
The P4 1 configuration means that the thermostat will start operating after 1 minute. After configuring the digital tube, it will not turn on, up to 1 minute after normal work. Long press established to activate again.
P5 is established as deactivated by default. Once the user establishes the temperature, the P5 can be established to prevent others from changing it at will. Once established in ON, the data will be blocked and the P5 will be established in off when necessary to configure them again.
ProductSiteLaunchDate : 2025-05-08T18:54:47.149Z
Size : 12V red and blue display
Style : 12V red and blue display
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1