Cart 2 india
In2Cart
Rs. 0
0
Product Information
Editorial Review
This specially made file is used for deburring and smoothing off the ends of the frets on a guitar or other fretted instrument. This means the ends will be less sharp and less likely to be uncomfortable while playing the instrument. Sharp fret ends are especially problematic after the fingerboard shrinks a little and the frets stick out the sides of the board. By rounding off the corners of the frets on a new guitar they will not become a nuisance as they begin to protrude out the sides of the fingerboard over time. The file can also be used on older guitars which already have sharp or protruding fret ends. The file has two smooth edges, these are used against the timber fingerboard and are smooth so they will safely glide over the timber and not dig into the fingerboard. The cutting edges are then used to take off the corners of the fret. With a little practice a full fingerboard only takes a matter of minutes. There is no need to take off a lot of the fret, just the very corner. One or two strokes on each corner of each fret may be all that is needed. It is ideal to round the corner of the fret off right down to where it meets the fingerboard, so particular attention should be given to angling the file so that rounds off this part of the fret and not just the top edge.
Features
1) High-quality file for guitar fret ends
2) Used for deburring and smoothing off fret ends
3) Made in Japan - Hardened tool steel
4) 2 cutting sides, 2 smooth sides
5) 6" (150mm) total length
Specification
Brand : Hiroshima
EAN : 0727973460531
Label : Uo-Chikyu
Manufacturer : Uo-Chikyu
PackageDimensions_Weight : 5.00 hundredths pounds
PackageDimensions : L:6.50 X W:0.70 X H:0.02
ProductGroup : Musical Instruments
ProductTypeName : INSTRUMENT_PARTS_AND_ACCESSORIES
Publisher : Uo-Chikyu
Studio : Uo-Chikyu
Title : Guitar Fret End Dressing File by Uo-Chikyu Hiroshima
This specially made file is used for deburring and smoothing off the ends of the frets on a guitar or other fretted instrument. This means the ends will be less sharp and less likely to be uncomfortable while playing the instrument. Sharp fret ends are especially problematic after the fingerboard shrinks a little and the frets stick out the sides of the board. By rounding off the corners of the frets on a new guitar they will not become a nuisance as they begin to protrude out the sides of the fingerboard over time. The file can also be used on older guitars which already have sharp or protruding fret ends. The file has two smooth edges, these are used against the timber fingerboard and are smooth so they will safely glide over the timber and not dig into the fingerboard. The cutting edges are then used to take off the corners of the fret. With a little practice a full fingerboard only takes a matter of minutes. There is no need to take off a lot of the fret, just the very corner. One or two strokes on each corner of each fret may be all that is needed. It is ideal to round the corner of the fret off right down to where it meets the fingerboard, so particular attention should be given to angling the file so that rounds off this part of the fret and not just the top edge.
Features
1) High-quality file for guitar fret ends
2) Used for deburring and smoothing off fret ends
3) Made in Japan - Hardened tool steel
4) 2 cutting sides, 2 smooth sides
5) 6" (150mm) total length
Specification
Brand : Hiroshima
EAN : 0727973460531
Label : Uo-Chikyu
Manufacturer : Uo-Chikyu
PackageDimensions_Weight : 5.00 hundredths pounds
PackageDimensions : L:6.50 X W:0.70 X H:0.02
ProductGroup : Musical Instruments
ProductTypeName : INSTRUMENT_PARTS_AND_ACCESSORIES
Publisher : Uo-Chikyu
Studio : Uo-Chikyu
Title : Guitar Fret End Dressing File by Uo-Chikyu Hiroshima
