Cart 2 india

Specification
AutoPartPosition : front
Brand : Diode Dynamics
BulletPoint1 : Compatible with Toyota FJ Cruiser Rear Turn Signal bulbs.
BulletPoint2 : Four COB type LEDs with a single high-power chip mounted at the top.
BulletPoint3 : Plug and play, no modification needed.
BulletPoint4 : Increased output with LED appearance.
BulletPoint5 : Backed with a 3-year warranty.
Color : Red
CompatibleWithVehicleType : Car
ExteriorFinish : Machined
ExternallyAssignedProductIdentifier : 6013136247236
ExternallyAssignedProductIdentifier1 : 0707181866554
ExternallyAssignedProductIdentifier2 : 707181866554
FitType : Vehicle Specific
IsAssemblyRequired : 1
ItemName : Diode Dynamics Rear Turn Signal LEDs compatible with Toyota FJ Cruiser 2013-2014 (pair), 7440 HP11 Red
ItemPackageDimensions_Height : 1 inches
ItemPackageDimensions_Length : 6 inches
ItemPackageDimensions_Width : 10 inches
ItemPackageQuantity : 1
ItemTypeKeyword : automotive-turn-signal-light-bulbs
Manufacturer : Diode Dynamics
Material : Plastic
ModelName : TYC 12-5361-00 Replacement front_right Turn Signal Lamp for FORD EDGE
ModelNumber : 12-5361-00
NumberOfBoxes : 1
NumberOfItems : 1
OemEquivalentPartNumber : FT4Z 13200 G
PartNumber : DD0108P
ProductDescription :

Features

• Modern LED appearance with instant on and off.
• Compatible with Toyota FJ Cruiser rear turn signal bulbs.
• Plug and play no modification with factory 7440 bulb size.
• Multiple brightness levels available.

Overview

LED Indicators. The factory incandescent rear turn signals on your vehicle illuminate in a slow glow taking a moment to turn off and on. With replacement LED bulbs you can immediately update your vehicle with the instant on-off blinking of modern LEDs. This instant activation adds a modern and distinct look to your vehicle.

Brightness. All Diode Dynamics LED lighting is rated with accurate measured lumen figures not calculations or guesses. We test the true output in-house and provide you the real numbers to compare.

Correct Color. You'll see that we offer both a red and amber option which meet SAE/DOT amber and red requirements. If you have a clear lens or an amber reflector over the turn signal bulb on your vehicle amber is the correct emitter color for maximum turn signal output. If your vehicle has a red lens over the rear turn signal then red is the correct emitter for you.

Reduced Load. When it comes to LED upgrades you'd think the lower power draw would be a great feature! However this can cause a hyperblink or fast-blinking turn signal which can be corrected with LED Resistors or an LED Flasher (sold separately).

The most basic tried-and-true method to correct hyperblinking is to add resistors (sold separately). Since a 6-ohm resistor uses about the same power as a standard turn signal bulb these can be used on any vehicle but does require tapping factory signals. One resistor is needed to replace each turn signal bulb.

ProductSiteLaunchDate : 2020-12-23T22:34:17.320Z
Size : HP11 (310 lumens)
SpecificUsesForProduct : Signalling Light
StreetDate : 2020-03-11T00:00:01Z
Style : TYC
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredDgHzRegulation1 : not_applicable
SupplierDeclaredDgHzRegulation2 : not_applicable
SupplierDeclaredDgHzRegulation3 : not_applicable
SupplierDeclaredDgHzRegulation4 : not_applicable
SupplierDeclaredDgHzRegulation5 : not_applicable
UnitCount : 2
UnspscCode : 25172907
Voltage : 12 volts
WarrantyDescription : Amazon Warranty