Cart 2 india

Specification
Brand : CONFAST
BulletPoint1 : MADE FROM 304 STAINLESS STEEL - Can be used in wet, submerged environments and will not rust
BulletPoint2 : WIDE RANGE OF SIZES - Insures proper fastener for best results
BulletPoint3 : PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
BulletPoint4 : HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
BulletPoint5 : Type: Wedge Anchor
BulletPoint6 : ⚠ Important: the nut and washer must be taken off the anchor prior to using the installation tool. Failure to do so will result in damage to the tool that will not be covered by warranty.
Color : Silver
CompatibleGrooveDiameter : 0.25 inches
ExteriorFinish : Stainless Steel
ExteriorFinish1 : Stainless Steel
ExteriorFinish2 : Zinc
ExternallyAssignedProductIdentifier1 : 014973180249
ExternallyAssignedProductIdentifier2 : 738287503838
ExternallyAssignedProductIdentifier3 : 0014973180249
ExternallyAssignedProductIdentifier4 : 0738287503838
ExternallyAssignedProductIdentifier5 : 00738287503838
FinishType : Plain
GradeRating : Grade 304
IncludedComponents : Anchors(25)^Hex Nuts(25)^Flat Washers(25)
ItemDisplayDimensions_Length : 3.38 inches
ItemDisplayWeight : 3.2 pounds
ItemName : CONFAST 1/4" x 2-1/4" Stainless Steel Wedge Anchor (100 per Box)
ItemPackageDimensions_Height : 3 inches
ItemPackageDimensions_Length : 6 inches
ItemPackageDimensions_Width : 3.5 inches
ItemPackageQuantity : 1
ItemShape : Wedge
ItemTypeKeyword : wedge-anchors
Manufacturer : CONFAST
ManufacturerGrade : Grade 2
Material : Stainless Steel 304
MaximumShearStrength : 1082
MeasurementSystem : Imperial
MetalType : Carbon Steel
ModelNumber : 14973180249
NumberOfItems : 100
NumberOfPieces : 100
PackageLevel : unit
PartNumber : WAS14214
ProductDescription : Applications
The anchor is made from 304 Stainless Steel. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Wet environment.

Hole Diameter/Bit Diameter
The anchor requires a 1/4" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 1/4".

Length Anchor
The length of the anchor is 2-1/4"

Thread Length
The length of the threads on the anchor is 1-1/8" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 1-1/8". Therefore, the anchor must be installed so that a minimum of 1-1/8" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 7/8". This will ensure that the minimum embedment of 1-1/8" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/4" diameter anchor requires the hole in the fixture to be 5/16".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 5 - 10 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 2-1/2" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 1-1/4" from an unsupported edge of the concrete.
ProductSiteLaunchDate : 2017-06-08T04:32:47.726Z
Size : One Size
Style : tie Wire
SupplierDeclaredDgHzRegulation : not_applicable
UnitCount : 25
UnspscCode : 31161500